Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2121-2140 of 3257
-
Experimental Micro Mechanics Methods for Conventional and Negative Poisson’s Ratio Cellular Solids as Cosserat Continua
(The American Society of Mechanical Engineers (ASME), 1991)Continuum representations of micromechanical phenomena in structured materials are described, with emphasis on cellular solids. These phenomena are interpreted in light of Cosserat elasticity, a ... -
Tearing Modulus Analysis for Pipes Containing Constant Depth Internal Flaw
(The American Society of Mechanical Engineers (ASME), 1991)The pipe displacement and tearing modulus solutions are derived for pipes containing a uniform depth internal flaw under bending moment or axial loading. The tearing modulus solution is derived ... -
Single Crystal Modeling for Structural Calculations: Part 2—Finite Element Implementation
(The American Society of Mechanical Engineers (ASME), 1991)This paper is devoted to the implementation in a finite element code of a micro-macro anisotropic viscoplastic model for F.C.C. single crystals derived from the slip theory. It shows ... -
Effect of Ripple Load on Stress-Corrosion Cracking in Structural Steels
(The American Society of Mechanical Engineers (ASME), 1991)The presence of small ripple loading can, under certain circumstances, significantly reduce time-to-failure and threshold stress intensity for stress-corrosion cracking (SCC) of steels. A predictive ... -
Microhardness of the Surface Layer of Tungsten and Molybdenum After Recrystallization With Laser Radiation
(The American Society of Mechanical Engineers (ASME), 1991)We present results of microhardness measurements in melted local regions in molybdenum and tungsten. Microhardness has been measured by the Vickers method. Melted regions have been produced by ... -
Modeling of Plane Strain Fatigue Crack Closure
(The American Society of Mechanical Engineers (ASME), 1991)Mechanisms and models proposed for plane strain fatigue crack closure are evaluated. A mechanism based on out-of-plane plastic strain component, εz p , in plane strain is shown not to be ... -
Characterization of Fatigue Crack Growth in Intermediate and Large Scale Yielding
(The American Society of Mechanical Engineers (ASME), 1991)Parameters previously proposed for the correlation of elastic-plastic fatigue crack growth data are critically reviewed and compared from a pragmatic engineering standpoint. Commonly employed estimates ... -
Constitutive Modeling of Metals Under Nonproportional Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1991)A two-surface kinematic hardening model for the stress-strain response of metals under nonproportional tension-torsion cyclic loading is developed and verified with critical experiments. In this ... -
Application of Neutron Diffraction to Measure Residual Strains in Various Engineering Composite Materials
(The American Society of Mechanical Engineers (ASME), 1991)An experimental neutron diffraction technique was used to measure residual strains that developed in multiphase composite materials during postfabrication cooling as a result of thermal expansion ... -
Evaluation of a Modified Monotonic Neuber Relation
(The American Society of Mechanical Engineers (ASME), 1991)It has been proposed in the literature that the Neuber relation be modified to read Kε/Kt × (Kσ/Kt)m = 1 in order to improve its predictive capability when plane strain loading conditions ... -
Measuring Residual Stresses by Hole-Drilling and Coherent Optics Techniques: A Numerical Calibration
(The American Society of Mechanical Engineers (ASME), 1991)Hole-drilling is a widely accepted method for determining residual stresses from the relaxation data obtained by a strain-gage rosette. Several researchers have recently investigated the alternative ... -
Friction Models for Metal Forming in the Boundary Lubrication Regime
(The American Society of Mechanical Engineers (ASME), 1991)Wilson and Shen’s semi-empirical equation for the effective hardness of a plastically deforming workpiece is used to develop models for tool-workpiece friction in metal-forming processes operating ... -
Deformation Heating During Cold Rolling of Aluminum Strips
(The American Society of Mechanical Engineers (ASME), 1991)The temperature rise due to plastic work and interfacial frictional forces during cold rolling of aluminum and steel strips is investigated. The predictions of a two-dimensional thermal-mechanical ... -
A Study on Burr Formation Mechanism
(The American Society of Mechanical Engineers (ASME), 1991)A quantitative model of burr formation for ductile materials which does not include fracture during orthogonal machining is proposed. The burr formation mechanism is divided into three parts—initiation, ... -
Improvement of Fatigue Crack Growth Resistance by Serrated Grain Boundary at High Temperature
(The American Society of Mechanical Engineers (ASME), 1991)Effects of serrated grain boundaries on the improvement of fatigue-crack growth resistance were investigated using austenitic 21Cr-4Ni-9Mn heat-resisting steel at 973K in air. Grain boundaries were ... -
A One-Dimensional, Two-Phase Flow Model for Taylor Impact Specimens
(The American Society of Mechanical Engineers (ASME), 1991)In this paper, a simple theoretical analysis of an old problem is presented. The analysis is more complete than earlier versions, but retains the mathematical simplicity of the earlier versions. ... -
Biaxial Low Cycle Fatigue of Unaged and Aged 1Cr-1Mo-1/4V Steels at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1991)This paper describes the biaxial low cycle fatigue of unaged and aged 1Cr-1Mo-1/4V rotor steels at 823 K in air. Combined push-pull and reversed torsion tests were carried out on these steels ... -
Room Temperature Formability and Fracture Behavior of a High Strength AI-Zn-Mg Alloy
(The American Society of Mechanical Engineers (ASME), 1991)The formability and fracture behavior of a high strength, aluminum alloy made to (French) specification AFNOR 7020 is reported. The formability study included the evaluation of the room temperature ... -
Discussion: “A Method for Dynamic Fracture Initiation Testing of Ceramics” (Duffy, J., Suresh, S., Cho, R., and Boff, E. R., 1988, ASME J. Eng. Mater. Technol., 110, pp. 326–331; Addendum, 1989, ASME J. Eng. Mater. Technol., 111, p. 86)
(The American Society of Mechanical Engineers (ASME), 1991)NOTE: The reference to the original article for the discussion “A Method for Dynamic Fracture Initiation Testing of Ceramics” (pp. 183–185) is incorrectly cited in the original PDF. The volume ... -
A Method for Estimation of the Fracture Toughness of CrMoV Rotor Steels Based on Composition
(The American Society of Mechanical Engineers (ASME), 1991)Assessment of the remaining life of steam turbine rotors in the presence of bore defects requires a knowledge of the fracture toughness (KIC ) of the rotors. Current procedures for estimating ...