Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2101-2120 of 3257
-
Use of the Shadow Optical Method of Caustics to Predict Fatigue Crack Growth in Compression
(The American Society of Mechanical Engineers (ASME), 1992)The shadow optical method of caustics has been applied to the measurement of the bulging out of the surface of aluminum alloy 7075-T6 in the vicinity of a blunt notch in a single edge notch ... -
Cyclic Stress-Strain Behavior and Low-Cycle Fatigue of Ti 6-4 at 260°C
(The American Society of Mechanical Engineers (ASME), 1992)Low-cycle fatigue tests on Ti 6-4 (Ti-6Al-4V) have been carried out at 260°C under strain-controlled conditions with constant strain amplitude and increasing multistep strain levels. The ... -
Enhancement of Thermal Conductivities in Polymeric Fiber Reinforced Composite Materials
(The American Society of Mechanical Engineers (ASME), 1992)In this study it is demonstrated that thermal conductivities of polymeric fiber-reinforced composite materials can be enhanced by using coated fibers and by adding thermally conductive microspheres ... -
Models for Inelastic Deformation of Particles Associated With Hot Pressing of Metal Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1992)During fabrication of fiber reinforced metal-matrix composites by hot pressing, fiber breakage due to particles impingement during consolidation of fiber/particle system is very common. In studying ... -
A State Variable Modeling of Plasticity and Necking Under Uniaxial Tension
(The American Society of Mechanical Engineers (ASME), 1992)Constitutive equations based on a state variable modeling of the thermo-viscoplastic behavior of metals are discussed, and incorporated in an exact, long-wavelength analysis of the neck-growth ... -
An Analysis of the Thin-Walled Torsion Specimen
(The American Society of Mechanical Engineers (ASME), 1992)A detailed finite element analysis has been conducted of the thin-walled torsion specimen. This specimen, when properly gripped, provides an approximation to the simple shear deformation field. ... -
On the Analysis of Distortion and Residual Stress in Carburized Steels
(The American Society of Mechanical Engineers (ASME), 1992)This paper appraises the accuracy with which distortion and residual stress can be predicted in carburized and quenched gear steels. An experimental sample is heattreated such that a nonsymmetric ... -
Consideration of Phase Transformations in the Study of Shear Bands in a Dynamically Loaded Steel Block
(The American Society of Mechanical Engineers (ASME), 1992)We study plane strain thermomechanical deformations of a square block made of steel, and model a material defect in it by a rigid non-heat-conducting ellipsoidal inclusion located at the center ... -
Nonisothermal Constitutive Model for the Small Strain Behavior of 9Cr-1 Mo-V-Nb Pressure Vessel Steel
(The American Society of Mechanical Engineers (ASME), 1992)A viscoplastic constitutive model characterization is presented for the small strain, nonisothermal behavior of a 9Cr-1Mo-V-Nb pressure vessel steel between 25°C and 600°C. A framework ... -
Variation of Yield Stress With Strain Rate for Three Carbon Steels
(The American Society of Mechanical Engineers (ASME), 1992)This paper presents an experimental study of the strain-rate and temperature dependence of the yield stress for three low carbon steels (percent c = 0.2, 0.3, and 0.4). Tension test results ... -
A Phenomenologically Based Constitutive Model for René 95
(The American Society of Mechanical Engineers (ASME), 1992)A unified constitutive model incorporating internal state variables based upon the deformation phenomena that are observed to occur at the microstructural level has been developed and applied to ... -
Single Crystal Modeling for Structural Calculations: Part 1—Model Presentation
(The American Society of Mechanical Engineers (ASME), 1991)A micro-macro model derived from slip theory is shown. It is applied to the modeling of nickel base single crystal superalloys. The experimental data include monotonic and cyclic solicitations ... -
Stress Intensity Factors for a Cracked Stiffened Sheet With Cracked Stiffeners
(The American Society of Mechanical Engineers (ASME), 1991)The stress intensity factors are calculated for a cracked sheet and cracked stiffeners attached with rivets. The approach adopted is based on compatibility of displacements among the sheet, ... -
Fracture Toughness JIC Prediction From Super-Small Specimens (0.2CT, 0.5MM Thick) of a Martensitic Stainless Steel HT-9
(The American Society of Mechanical Engineers (ASME), 1991)The fracture toughness of alloy HT-9, a martensitic stainless steel under consideration for fusion reactor applications, was determined from 0.2CT (0.5mm thick) specimens. Specimens with thicknesses ... -
Locating and Sizing Disbonds in Glassfibre-Reinforced Plastic Plates Using Shearography
(The American Society of Mechanical Engineers (ASME), 1991)Shearography is a double-exposure optical method which reveals defects in components from anomalies in interferometric fringe patterns. In this paper, disbonds of known shapes and sizes are ... -
Buckling and Growth of Delamination in Thermoset and Thermoplastic Composites
(The American Society of Mechanical Engineers (ASME), 1991)Compression instability growth of through-width delaminations in composite laminates is investigated. A previously developed beam model that incorporates effects of elastic restraint at the ends ... -
Optimal Design for Two-Dimensional Structures Made of Composite Materials
(The American Society of Mechanical Engineers (ASME), 1991)The paper deals with the problem of finding the optimal orientation of orthotropic properties for an elastic body, subjected to a plane state of stress, in order to maximize the stiffness of ... -
Effect of Deformation-Induced Heating on the Cold Drawing of Polymeric Films
(The American Society of Mechanical Engineers (ASME), 1991)The destabilizing effect of deformation-induced heating on the cold drawing of polymeric films is investigated under adiabatic and plane-strain loading conditions. An approximate method, previously ... -
Thermomechanical Behavior of Anisotropic Inelastic Composites: A Micromechanical Theory
(The American Society of Mechanical Engineers (ASME), 1991) -
In-Phase and Out-of-Phase Multiaxial Fatigue
(The American Society of Mechanical Engineers (ASME), 1991)In this investigation, thin-walled circular cylindrical specimens fabricated from a low alloy pressure vessel steel (ASTM A-516 Gr. 70) were subjected to various multiaxial loading conditions. The ...