Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2021-2040 of 3257
-
A Spectral Element Simulation of Gravitational Flow During Plastic Pipe Extrusion
(The American Society of Mechanical Engineers (ASME), 1993)When plastic pipe is extruded, it emerges from an annular die and passes through a sizing sleeve to set its outer diameter. The pipe is then solidified in a cooling tank by spraying the ... -
The Influence of Grain Size on the Toughness of Monolithic Ceramics
(The American Society of Mechanical Engineers (ASME), 1993)Experiments have shown that there may be an optimal grain size which maximizes the toughness of polycrystalline ceramics. In this paper, we attempt to develop a theoretical model which can ... -
General-Form Solution of Shock Fitting Equation Including Die Wall Friction for the Multishock Powder Compaction
(The American Society of Mechanical Engineers (ASME), 1993)In this paper, shock fitting equations including wall friction force for predicting the one-dimensional compaction process of a powder medium caused by punch impact are first derived. The medium ... -
The Variable Threshold Rod Experiment: A Comparison of Measured and Computed Deformations
(The American Society of Mechanical Engineers (ASME), 1993)A novel experiment has been developed to induce inhomogeneous deformations under simple extension boundary conditions. By appropriate prior cold working of stock material and fabrication of test ... -
Prediction of Residual Stresses in Butt Welded Plates Using Inherent Strains
(The American Society of Mechanical Engineers (ASME), 1993)The source of residual stresses in the vicinity of a weld may be expressed in terms of inherent strains. The characteristics of the inherent strain distributions in butt welds are investigated. ... -
A General Fatigue Theory and Its Application to Out-of-Phase Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1993)Results of an experimental investigation of a constant-amplitude, fully reversed biaxial tension-compression out-of-phase cyclic loading are presented first. An energy-based fatigue theory is extended ... -
Fatigue Damage in Cross-Ply Titanium Metal Matrix Composites Containing Center Holes
(The American Society of Mechanical Engineers (ASME), 1993)The development of fatigue damage in four [0/90]s SCS-6/Ti-15-3 laminates containing center holes was investigated. A methodology to predict damage initiation based on an effective strain parameter ... -
The Use of Classification Zones for Fatigue Behavior in Steels—2
(The American Society of Mechanical Engineers (ASME), 1993)This is the second and updated version of a paper with a similar name, that was published in this journal in [1], 1977. The basic idea of classification of the Fatigue Regime is implemented ... -
Fatigue of AZ91E-T6 Cast Magnesium Alloy
(The American Society of Mechanical Engineers (ASME), 1993)The purpose of this research was to obtain room temperature fatigue behavior of AZ91E-T6 cast magnesium alloy and to determine if commonly used models that depict fatigue behavior are applicable ... -
Application and Verification of Fatigue Life Calculation Methods for AZ91E-T6 Cast Magnesium Alloy Under Variable Amplitude Loading
(The American Society of Mechanical Engineers (ASME), 1993)The goal of this research was to determine the applicability of commonly used fatigue life calculation methods for variable amplitude loading with sand cast AZ91E-T6 magnesium alloy using notched ... -
Mixed-Mode Fatigue Crack Propagation of Penny-Shaped Cracks
(The American Society of Mechanical Engineers (ASME), 1993)A three-dimensional penny-shaped crack under combined tensile and shear loadings is analyzed. The assumptions of Dugdale are applied to estimate the effects of plasticity around the edge of the ... -
A Simple and Efficient Multiaxial Fatigue Damage Model for Engineering Applications of Macro-Crack Initiation
(The American Society of Mechanical Engineers (ASME), 1993)This paper is devoted to the presentation of a multiaxial fatigue damage model, derived from Chaboche’s uniaxial formulation. Fit for use in the entire range of crack initiation life, it takes ... -
Strip Yield Analysis for Multiple Cracked Sheet With Riveted Stiffeners
(The American Society of Mechanical Engineers (ASME), 1993)An elasto-plastic analysis is conducted based upon a strip yield model for analyzing multiple cracks in a sheet reinforced with riveted stiffeners. Using the basic solution of a single crack ... -
Erratum: “Experimental Micro Mechanics Methods for Conventional and Negative Poisson’s Ratio Cellular Solids as Cosserat Continua” (Journal of Engineering Materials and Technology, 1991, 113, pp. 148–155)
(The American Society of Mechanical Engineers (ASME), 1993) -
Constitutive Equations for the Thermomechanical Response of René 80: Part 1—Development From Isothermal Data
(The American Society of Mechanical Engineers (ASME), 1993)This work describes the development of a unified nonisothermal constitutive model to predict the thermomechanical fatigue (TMF) response of a Nickel base superalloy, René 80. Nonisothermal ... -
ASME 1992 Nadai Lecture—Micromechanics of Inelastic Composite Materials: Theory and Experiment
(The American Society of Mechanical Engineers (ASME), 1993)Some recent theoretical and experimental results on modeling of the inelastic behavior of composite materials are reviewed. The transformation field analysis method (G. J. Dvorak, Proc. R. Soc. ... -
Constitutive Equations for the Thermomechanical Response of René 80: Part 2—Effects of Temperature History
(The American Society of Mechanical Engineers (ASME), 1993)The unified constitutive equations for René 80 developed by Bhattachar and Stouffer (1992) are used to predict the thermomechanical fatigue (TMF) response of a Nickel base superalloy René 80 ... -
An Evaluation of Gurson’s Theory of Dilatational Plasticity
(The American Society of Mechanical Engineers (ASME), 1993)Gurson’s constitutive theory for the plastic deformation of porous metals is specialized to small deformations of power-law solids containing a dilute concentration of voids, and the resulting ... -
Strain Hardening of Annealed 304 Stainless Steel by Creep
(The American Society of Mechanical Engineers (ASME), 1993)Combined axial-torsional experiments have been conducted at room temperature on thin-walled tubes to investigate the strain hardening behavior of annealed 304 stainless steel due to creep. The ... -
Editorial
(The American Society of Mechanical Engineers (ASME), 1992)