Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2001-2020 of 3257
-
Compression Failure in Reduced Adhesion Fiber Laminates
(The American Society of Mechanical Engineers (ASME), 1993)The compressive strength of fiber composites is of key interest in many strength critical composite structures, due to the generally lower failure values relative to tension dominated stress ... -
Special Section on Heat and Mass Transfer in Solidification Processing
(The American Society of Mechanical Engineers (ASME), 1993) -
A Comparison of the Strains Due to Edge Cracks and Cuts of Finite Width With Applications to Residual Stress Measurement
(The American Society of Mechanical Engineers (ASME), 1993)The strains on the surface near a loaded crack or cut are compared for cuts of different width to depth ratios. General solutions are obtained for an arbitrary distribution of normal and ... -
Parameter Evaluation for a Unified Constitutive Model
(The American Society of Mechanical Engineers (ASME), 1993)Parameters for the unified constitutive model MATMOD [1] were evaluated for rock salt (NaCl) by using nonlinear least squares to fit the model to isothermal laboratory data. MATMOD incorporates ... -
Compressive Failure of Fiber Composites: The Roles of Multiaxial Loading and Creep
(The American Society of Mechanical Engineers (ASME), 1993)The roles of multiaxial loading and creep in compressive failure of aligned fiber composites are considered. Analytical models are developed based on the model given by Budiansky and Fleck ... -
A Comparative Study of the Creep Rupture Properties of Type 316 Stainless Steel Base and Weld Metals
(The American Society of Mechanical Engineers (ASME), 1993)Creep rupture properties of a modified grade of type E316-15 stainless steel weld metal have been studied in the temperature range 823 to 923 K at different stress levels. The results are ... -
High Strain Rate Deformation and Damage in Ceramic Materials
(The American Society of Mechanical Engineers (ASME), 1993)The objective of this investigation is to use a plate impact recovery experiment to identify the dominant failure mechanisms in conventional α-Al2 O3 ceramics and thereby gain insight into the ... -
Toughening Mechanisms in Quasi-Brittle Materials
(The American Society of Mechanical Engineers (ASME), 1993)Fracture processes in cement-based materials are characterized by a large-scale fracture process zone, localization of deformation, and strain softening. Many studies have been conducted to understand ... -
Notch Ductile-to-Brittle Transition Due to Localized Inelastic Band
(The American Society of Mechanical Engineers (ASME), 1993)Holes are often drilled in a panel for cooling or fastening. For a panel made of a monolithic ceramic, such a hole concentrates stress, reducing load-carrying capacity of the panel by a ... -
Stochastic Aspects of Matrix Cracking in Brittle Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1993)A computer simulation of multiple cracking in fiber-reinforced brittle matrix composites has been conducted, with emphasis on the role of the matrix flaw distribution. The simulations incorporate ... -
Stable Crack Growth in Ceramics at Ambient and Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1993)Quasi-static, stable crack propagation tests in ceramics are presented. The tests are performed using a recently developed technique in which the crack mouth opening displacement (CMOD) is ... -
Cyclic Fatigue-Crack Growth in Grain Bridging Ceramics
(The American Society of Mechanical Engineers (ASME), 1993)Cyclic fatigue degradation is contemplated in polycrystalline ceramics exhibiting grain bridging as the principle toughening mechanism. A frictional-wear mechanism based on repetitive sliding wear ... -
Stable Crack Growth in Rate-Dependent Materials With Damage
(The American Society of Mechanical Engineers (ASME), 1993)A cohesive zone model of the Dugdale-Barenblatt type is used to investigate crack growth under small-scale-creep/damage conditions. The material inside the cohesive zone is described by a power-law ... -
Finite Element Simulations of Fiber Pull-Out
(The American Society of Mechanical Engineers (ASME), 1993)Fiber pull-out is simulated through a quasi-static analysis of a circular elastic cylinder with a rigid cylindrical fiber embedded in its center. The interface between the fiber and the matrix ... -
High Temperature Fracture Toughness in Silicon Nitride and Sialon
(The American Society of Mechanical Engineers (ASME), 1993)Fracture Toughness of HIP-sintered silicon nitride decreased with increasing temperature up to 1200°C. The brittle-to-ductile transition was observed in the temperature range from 1200°C ... -
Role of Crack Wake Toughening on Elevated Temperature Crack Growth in a Fiber Reinforced Ceramic Composite
(The American Society of Mechanical Engineers (ASME), 1993)Theoretical models were developed to predict the nature of the elevated temperature failure behavior in composites containing bridged cracks both for the case where crack front creep is absent ... -
Time Dependent Fracture and Cohesive Zones
(The American Society of Mechanical Engineers (ASME), 1993)This presentation is concerned with the fracture response of materials which develop cohesive or bridging zones at crack tips. Of special interest are concerns regarding crack stability as a ... -
Ultrasonic Assessment of Interfacial Oxidation Damage in Ceramic Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1993)A new approach to characterizing oxidation damage in ceramic matrix composites using ultrasonic techniques is proposed. In this approach the elastic constants of the composite are determined ... -
Computational Model of Flame-Cutting
(The American Society of Mechanical Engineers (ASME), 1993)A computational model for simulation of flame-cutting has been developed. Two different cutting conditions are compared with respect to the residual stresses. The first case is a plate cut at ... -
Special Issue Devoted to the Proceedings of the International Symposium on Micromechanics of Ceramics and Ceramic Composites
(The American Society of Mechanical Engineers (ASME), 1993)