Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1901-1920 of 3257
-
Dynamic Modeling and Control of Packing Pressure in Injection Molding
(The American Society of Mechanical Engineers (ASME), 1994)A dynamic model of injection molding developed from physical considerations is used to select PID gains for pressure control during the packing phase of thermo-plastic injection molding. The ... -
Measurement of Near Surface Residual Stresses Using Electric Discharge Wire Machining
(The American Society of Mechanical Engineers (ASME), 1994)In previous work it has been shown that near surface residual stresses may be deduced from surface strains produced by making a cut of progressively increasing depth. The process of electric ... -
How Affine is the Entanglement Network of Molten Low-Density Polyethylene in Large Amplitude Oscillatory Shear?
(The American Society of Mechanical Engineers (ASME), 1994)The nonlinear viscoelastic behavior of molten plastics is often attributed to interactions between long-chain molecules. Entanglement theories model this behavior with a network of junctions. Whether ... -
Local Buckling and Failure of Pultruded Fiber-Reinforced Plastic Beams
(The American Society of Mechanical Engineers (ASME), 1994)An experimental investigation of the local compression flange buckling and failure of commercially produced pultruded fiber-reinforced plastic (FRP) I-shaped beams is described in this paper. Results ... -
A Finite Element Analysis of Electromagnetic Forming for Tube Expansion
(The American Society of Mechanical Engineers (ASME), 1994)The electromagnetic field and dynamic deformation analyses for tube expansion by electromagnetic forming were performed by the finite element method. A realistic pressure distribution was calculated ... -
Fatigue Growth Analysis of an Inclined Crack Under Uniaxial Cyclic Loading in Materials With Different Yield Strengths in Tension and Compression
(The American Society of Mechanical Engineers (ASME), 1994)In the present paper, an improved strain-energy-density criterion presented recently for the commonly used fracture criterion, the minimum strain-energy-density criterion, is extended to the case ... -
A Fatigue Crack Growth Model for Single Overload Tests
(The American Society of Mechanical Engineers (ASME), 1994)Crack growth rate experiments are conducted by applying an intermediate single overload cycle in constant amplitude load (CAL) tests. For a particular overload ratio, three to four tests are ... -
Thermally Induced Fields in Electroelastic Composite Materials: Average Fields and Effective Behavior
(The American Society of Mechanical Engineers (ASME), 1994)The average thermally induced electroelastic fields and the effective thermal expansion and pyroelectric coefficients of two-phase composite materials are obtained by applying the Mori-Tanaka ... -
Creep Behavior of a Unidirectional SCS-6/Ti-15-3 Metal Matrix Composite at 450°C
(The American Society of Mechanical Engineers (ASME), 1994)As the first step to understand the creep behavior of a unidirectional SCS-6/Ti-15-3 metal matrix composite, creep tests were performed at 450°C using specimens reinforced with fibers oriented ... -
Influence of Weld Discontinuities on Strain Controlled Fatigue Behavior of 308 Stainless Steel Weld Metal
(The American Society of Mechanical Engineers (ASME), 1994)Detailed investigations have been performed for assessing the importance of weld discontinuities in strain controlled low cycle fatigue (LCF) behavior of 308 stainless steel (SS) welds. The LCF ... -
Deformation and Failure Behavior of Woven Composite Laminates
(The American Society of Mechanical Engineers (ASME), 1994)Conceptually, fabric composites have some structural advantages over conventional laminates. However, deformation and failure analyses become more complex with the additional anisotropy introduced ... -
Experimental Characterization of the Elastic-Plastic Strain Fields at the Crack Tip Due to Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1994)Some mechanical components cease to function satisfactorily, failing either under excessive elastic deformation or extensive plastic yielding. In the case of constrained plastification, the researcher ... -
A Yield Surface Approach to the Estimation of Notch Strains for Proportional and Nonproportional Cyclic Loading
(The American Society of Mechanical Engineers (ASME), 1994)An analytical method is developed to estimate notch root strains in a notched bar of elastic-plastic, isotropic material subjected to proportional and nonproportional multiaxial nominal loading. ... -
The Effect of Matrix Microstructure on Thermally Induced Residual Stresses in SiC/Titanium Aluminide Composites
(The American Society of Mechanical Engineers (ASME), 1994)This paper examines the effect of varying the microstructural composition of titanium aluminide on the evolution of residual stresses in titanium aluminide matrix composites. An analytical model ... -
Erratum: “On the Modeling of Nonproportional Cyclic Plasticity of Waspaloy” (Journal of Engineering Materials and Technology, 116, pp. 35–44)
(The American Society of Mechanical Engineers (ASME), 1994) -
Modeling the Effect of Oxidation on Damage in SiC/Ti-15-3 Metal Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1994)In this paper, a micromechanical analysis is performed on a single ply continuous fiber SiC/Ti-15V-3Al-3Sn-3Cr (Ti-15-3) metal matrix composite to study the complex interactions between the composite ... -
On the Propagation of a Shear Band in a Steel Tube
(The American Society of Mechanical Engineers (ASME), 1994)Marchand and Duffy tested thin-walled steel tubes in a split Hopkinson torsion bar at a nominal strain-rate of approximately 1600/s and could not determine conclusively whether a shear band ... -
Holographic Inspection of Plates Containing Areas of Localized Thickness Variation
(The American Society of Mechanical Engineers (ASME), 1994)Circular plates, under unknown clamping conditions and containing simulated defects in the form of circular localized thinning or thickening, are inspected by double-exposure holography. With an ... -
Creep, Stress Relaxation and Biaxial Ratchetting of Type 304 Stainless Steel After Cyclic Preloading
(The American Society of Mechanical Engineers (ASME), 1994)A series of tests for creep, stress relaxation, and biaxial ratchetting of type 304 stainless steel after cyclic preloading were carried out to investigate their interaction. The interesting ... -
A Constitutive Model for Anisotropic Creep Deformation
(The American Society of Mechanical Engineers (ASME), 1994)Anisotropic creep behavior of polycrystalline metals under repeated stress changes is modeled from a phenomenological point of view. The creep model consists of basic constitutive equations (BCE) ...