Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1841-1860 of 3257
-
A Nonlinear Kinematic Hardening Model for Elastoplastic Deformations in Grey Cast Iron
(The American Society of Mechanical Engineers (ASME), 1995)A kinematic hardening model including an associated flow rule is proposed for elastoplastic deformations in graphitic grey cast iron. Quantitatively good results are obtained when comparing with ... -
Plane-Strain Tension Tests on Aluminum Alloy Sheet
(The American Society of Mechanical Engineers (ASME), 1995)A simple way of making plane-strain tension tests on sheet specimens has been developed. This method was used to test sheets of aluminum alloy 2008 T4 and the results were analyzed in terms ... -
Analysis of Mass Transfer Process in the Pore Free Technique
(The American Society of Mechanical Engineers (ASME), 1995)Air entrainment is one of the most significant problems in pressure die casting. A possible solution is to use the Pore Free technique. In this technique an oxygen is introduced into the die ... -
The Mechanical Behavior of Zinc During Machining
(The American Society of Mechanical Engineers (ASME), 1995)It is well known that a nonzero force is obtained when cutting forces measured at different feed rates but otherwise constant cutting conditions are extrapolated to zero feed rate. In the ... -
Fatigue Design Model Based on Damage Mechanisms Revealed by Acoustic Emission Measurements
(The American Society of Mechanical Engineers (ASME), 1995)Integration of the microcomputer into acoustic emission instrumentation has brought AE monitoring of fatigue tests into the realm of practicality. On-line processing makes available a selection ... -
A New Perspective on the Influence of Thickness and Post-Weld Heat Treatment for Large Scale Welded Joints
(The American Society of Mechanical Engineers (ASME), 1995)CTOD, Charpy, and wide plate results from welded constructional steels are collected from nine companies. The resulting large data bank is analyzed statistically to identify general trends in ... -
An Investigation of the Effect of Speeds of Work Rolls on Rolling Strip
(The American Society of Mechanical Engineers (ASME), 1995)The paper is an investigation of strip curvature caused by the different speeds between the upper work roll and the lower work roll in the rolling process for an aluminum strip. At the same ... -
Strain Concentration Calculation of Fatigue
(The American Society of Mechanical Engineers (ASME), 1995)On the basis of the authors’ rule of sliding to transform elastic solution to plastic in a previous paper, a new method of calculating fatigue is developed by using ordinary relaxation methods ... -
A Phenomenological Model for Intergranular Failure by r-type and Wedge-Type Cavitation
(The American Society of Mechanical Engineers (ASME), 1995)Equations to predict local intergranular failure (by “r”-type and “wedge”-type cavitation and the coupling between them) have been developed. The derivation has utilized physically based concepts ... -
Shearographic and Holographic Assessment of Defective Laminates With Bond-Lines of Different Elasticities
(The American Society of Mechanical Engineers (ASME), 1995)While defects in laminated plates are readily revealed using double-exposure shearography and holography, when an incremental vacuum pressure is applied between the exposures, the apparent defect ... -
Deformation Analysis of Simple-Shear Sheet Specimens
(The American Society of Mechanical Engineers (ASME), 1995)The shear properties of different simple-shear sheet specimens were investigated using the elastic-plastic finite element method. Tension loaded specimens with a shear zone formed at the center ... -
Effect of Surface Asperity on Interfacial Contact Process Controlled by Power Law Creep—Numerical Study of Viscoplastic Adhering Process
(The American Society of Mechanical Engineers (ASME), 1995)An interfacial contact process due to power law creep is studied using a finite element technique. The contact process is assumed to be produced by power law creep alone after initial intimate ... -
Characterization of Elevated Temperature Crack Growth in Hastelloy-X Using Integral Parameters
(The American Society of Mechanical Engineers (ASME), 1995)Linear elastic fracture mechanics approaches are not suitable for prediction of fatigue crack growth in the nonlinear regime at elevated temperatures. The objective of this paper is to investigate ... -
Compressive Fatigue of a Plasma Sprayed Zr02-8 wt%Y203 and Zr02-10wt%NiCrAlCoY TTBC
(The American Society of Mechanical Engineers (ASME), 1995)High cycle (>106 cycles) fatigue (HCF) behavior of thick thermal barrier coatings (TTBC’s) was examined for applied stresses near the compressive strength of the material. Test data were ... -
Experimental Study of Interfacial Contacting Process Controlled by Power Law Creep
(The American Society of Mechanical Engineers (ASME), 1995)Interfacial contacting processes under a high temperature and a high bonding pressure (T = 973 K, P = 30 MPa) are experimentally studied, using oxygen free copper. The faying surfaces were ... -
Nonproportional Low Cycle Fatigue Criterion for Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1995)This paper describes a multiaxial low cycle fatigue parameter for correlating Hues under nonproportional loadings. Constant amplitude low cycle fatigue tests were carried out under 14 proportional ... -
Compressive Stress-Strain Relations and Shock Hugoniot Curves of Flexible Foams
(The American Society of Mechanical Engineers (ASME), 1995)Based on the general shape of the curves describing experimental compressive stress-strain relations of flexible porous materials (e.g., flexible foams) which are known to depend on their relative ... -
Corrosion Fatigue of AZ91E-T6 Cast Magnesium Alloy in a 3.5 Percent NaCl Aqueous Environment
(The American Society of Mechanical Engineers (ASME), 1995) -
Elastic Anisotropy Effect of Crystals on Polycrystal Fatigue Crack Initiation
(The American Society of Mechanical Engineers (ASME), 1995)Fatigue bands have been observed in both monocrystalline and polycrystalline metals. Extrusions and intrusions at the free surface of fatigued specimens are favorable sites for fatigue crack ... -
Thermoplastics as Engineering Materials: The Mechanics, Materials, Design, Processing Link
(The American Society of Mechanical Engineers (ASME), 1995)While the use of plastics has been growing at a significant pace because of weight reduction, ease of fabrication of complex shapes, and cost reduction resulting from function integration, the ...