Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1461-1480 of 3257
-
-
-
On the Limit of Surface Integrity of Alumina by Ductile-Mode Grinding
(The American Society of Mechanical Engineers (ASME), 2000)This paper investigates both experimentally and theoretically the subsurface damage in alumina by ductile-mode griding. It found that the distribution of the fractured area on a ground mirror ... -
Measurement of the Axial Residual Stresses Using the Initial Strain Approach
(The American Society of Mechanical Engineers (ASME), 2000)Traditionally, the unknown variables to be estimated in residual stress measurement are based on the approximation of the stresses. In this paper an alternative approach is presented, in which ... -
Effect of Plasma Cutting on the Fatigue Resistance of Fe510 D1 Steel
(The American Society of Mechanical Engineers (ASME), 2000)The paper describes the results of a research programme, carried out at the Department of Aerospace Engineering of the University of Pisa, for the assessment of the influence of plasma cutting ... -
An Investigation of Yield Potentials In Superplastic Deformation
(The American Society of Mechanical Engineers (ASME), 2000)Recent results (Khraisheh et al., 1995 and 1997) have indicated that superplastic materials exhibit a strong degree of anisotropy and that the plastic flow cannot be described by the isotropic ... -
Cold Compaction of Composite Powders
(The American Society of Mechanical Engineers (ASME), 2000)Densification behavior of composite powders was investigated under cold compaction. Experimental data were obtained for mixed copper and tungsten powders with various volume fractions of tungsten ... -
Modeling of Irradiation Embrittlement of Reactor Pressure Vessel Steels
(The American Society of Mechanical Engineers (ASME), 2000)A model to describe the change in the inelastic and fracture properties of reactor pressure vessel steels due to neutron irradiation in the ductile region (i.e., irradiation embrittlement) is ... -
Failure of a Ductile Adhesive Layer Constrained by Hard Adherends
(The American Society of Mechanical Engineers (ASME), 2000)The evaluation of a fracture from a thin layer constrained by a hard material is important in relation to the structural integrity of adhesive joints and composite materials. It has been ... -
High Strain Extension of Open-Cell Foams
(The American Society of Mechanical Engineers (ASME), 2000)The high strain tensile deformation of open-cell foams is analyzed, using a Kelvin foam lattice model. The stretching, bending, and twisting of elastic cell edges is analyzed, and the deformed ... -
Influence of Heat Treatment on the Mechanical Properties and Damage Development in a SiC/Ti-15-3 MMC
(The American Society of Mechanical Engineers (ASME), 2000)Titanium alloys are commonly heat-treated to meet specific design requirements. In an effort to possibly create a better composite, the influence of heat treatments on the damage evolution and ... -
Cyclic Deformation Behavior and Dislocation Substructures of Hexagonal Zircaloy-4 Under Out-of-Phase Loading
(The American Society of Mechanical Engineers (ASME), 2000)Macroscopic response and microscopic dislocation structures of Zr-4 subjected to biaxial fatigue under different phase angles of 30°, 60°, 90° and different equivalent strain ranges ... -
Numerical Analysis of Welding Residual Stress and Its Verification Using Neutron Diffraction Measurement
(The American Society of Mechanical Engineers (ASME), 2000)Direct measurements and computed distributions of through-thickness residual stress in a pipe butt-welded joint and a pipe socket-welded joint are compared. The analytical evaluation methods used ... -
Models for Cyclic Ratchetting Plasticity—Integration and Calibration
(The American Society of Mechanical Engineers (ASME), 2000)Three well-known ratchetting models for metals with different hardening rules were calibrated using uniaxial experimental data from Bower (1989) [J. Mech. Phys. Solids, 31 , pp. 455–470], and ... -
Interfacial Stresses and Void Nucleation in Discontinuously Reinforced Composites
(The American Society of Mechanical Engineers (ASME), 2000)This paper presents the theoretical predictions of the stress state at the inclusion-matrix interface in discontinuous metal matrix composites by the generalized inclusion method. In the author’s ... -
Effect of Laser Shock Processing (LSP) on the Fatigue Resistance of an Aluminum Alloy
(The American Society of Mechanical Engineers (ASME), 2000)The laser shock induced stress wave is described and measured with a polyvinylidene fluoride (PVDF) transducer. A principle for selecting laser parameters is proposed. A small sized laser with ... -
Residual Stress Reduction and Fatigue Strength Improvement by Controlling Welding Pass Sequences
(The American Society of Mechanical Engineers (ASME), 2000)The effects of residual stress on fatigue strength at a weld toe in a multi-pass fillet weld joint were evaluated. The residual stresses in the weld joints were varied by controlling the ... -
Consistent and Minimal Springback Using a Stepped Binder Force Trajectory and Neural Network Control
(The American Society of Mechanical Engineers (ASME), 2000)One of the greatest challenges of manufacturing sheet metal parts is to obtain consistent part dimensions. Springback, the elastic material recovery when the tooling is removed, is the major ... -
Model of Grain Deformation Method for Evaluation of Creep Life in In-Service Components
(The American Society of Mechanical Engineers (ASME), 2000)The creep life can be evaluated by the degree of grain deformation since the grains of Cr-Mo base material deform in the direction of stress. The grain deformation method using image-processing ... -
Study of Surface Residual Stress by Three-Dimensional Displacement Data at a Single Point in Hole Drilling Method
(The American Society of Mechanical Engineers (ASME), 2000)A method combining moiré interferometry, Twyman–Green interferometry, and blind hole drilling method is proposed for simple and accurate determination of residual stress. The relationship between ...