Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1341-1360 of 3257
-
Micro and Macro Deformation of Single Crystal NiTi
(The American Society of Mechanical Engineers (ASME), 2002)We present experimental results on the instrumented Vickers micro-indentation and compression of solutionized Ni-rich NiTi single crystals. The tests are conducted at room temperature where the ... -
A Study of Residual Stresses and Microstructure in 2024-T3 Aluminum Friction Stir Butt Welds
(The American Society of Mechanical Engineers (ASME), 2002)Three-dimensional residual stress mapping of an aluminum 2024-T3 arcan specimen, butt-welded by the friction stir technique, was performed by neutron diffraction. Results indicate that the residual ... -
On the Improvement of Calibration Coefficients for Hole-Drilling Integral Method: Part I—Analysis of Calibration Coefficients Obtained by a 3-D FEM Model
(The American Society of Mechanical Engineers (ASME), 2002)One of the important factors affecting the accuracy of stress values obtained from the hole-drilling method is the calibration coefficient. A three-dimensional model was established to determine ... -
Effects of Shot-Peening on Fretting-Fatigue Behavior of Ti-6Al-4V
(The American Society of Mechanical Engineers (ASME), 2002)The effects of shot-peening on the fretting fatigue behavior of titanium alloy, Ti-6Al-4V were investigated. Specimens were shot-peened as per AMS 2432 standard. X-ray diffraction analysis measured ... -
On the Elastic Properties of PVD Coatings in Relation to Their Microstructure
(The American Society of Mechanical Engineers (ASME), 2002)Physical vapor deposited (PVD) coatings have low effective stiffness Eeff (as compared to the bulk material) in directions parallel to the substrate. It increases with an increasing residual ... -
Damage Zone Around Tip of an Interface Crack Between Rubber-Modified Epoxy Resin and Aluminum
(The American Society of Mechanical Engineers (ASME), 2002)The fracture behavior of an interface crack tip has significant influence on the structural integrity of an adhesive joint. We investigate a damage zone and the deformation of rubber particles ... -
Residual Stress Measurement in a Ceramic-Metallic Graded Material
(The American Society of Mechanical Engineers (ASME), 2002)This paper presents experimental measurements of the through-thickness distribution of residual stress in a ceramic-metallic functionally graded material (FGM). It further presents an error analysis ... -
Analysis of High Volume Fraction Irregular Particulate Damping Composites
(The American Society of Mechanical Engineers (ASME), 2002)Concentrated suspensions of inclusions occur in asphalt and dental composite resins. Concentrated suspensions are also of use in achieving a combination of high stiffness and loss (the product ... -
Three-Dimensional Finite Element Analysis of the Cold Expansion of Fastener Holes in Two Aluminum Alloys
(The American Society of Mechanical Engineers (ASME), 2002)A three-dimensional finite element analysis is developed for the cold expansion process in two aluminum alloys, 2024-T351 and 7050-T7451. The entire cold working process including hole expansion, ... -
In Situ Matrix Shear Response Using Torsional Test Data of Fiber Reinforced Unidirectional Polymer Composites
(The American Society of Mechanical Engineers (ASME), 2002)The in situ shear response of the matrix in polymer matrix composites (PMC) has been studied. Torsion tests were performed on solid cylinders of unidirectional glass fiber reinforced/vinylester ... -
Relationship Between Rockwell C Hardness and Inelastic Material Constants
(The American Society of Mechanical Engineers (ASME), 2002)This paper describes the relationship between Rockwell C hardness and elastic-plastic material constants by using finite element analyses. Finite element Rockwell C hardness analyses were carried ... -
Effect of Strain Gradients and Heterogeneity on Flow Strength of Particle Reinforced Metal-Matrix Composites
(The American Society of Mechanical Engineers (ASME), 2002)This paper deals with an analysis of the size effect on the flow strength of metal-matrix composites due to the presence of geometrically necessary dislocations. The work is based upon a cell ... -
Some Plastic Deformation Modes for Indentation of Half Space by a Rigid Body With Serrated Surface as a Model of Roughness Transfer in Metal Forming
(The American Society of Mechanical Engineers (ASME), 2002)This paper is concerned with the plastic deformation modes of the free surface of the half space between the teeth on the serrated surface of a rigid body. The rigid body indents the half ... -
Surface Texture, Fatigue, and the Reduction in Stiffness of Fiber Reinforced Plastics
(The American Society of Mechanical Engineers (ASME), 2002)In this study the influence of machined surface texture on the fatigue strength of a Graphite/Bismaleimide (Gr/Bmi) laminate was examined. Rectangular beam specimens were machined to achieve ... -
Development of an Analytical Model for Drilling Burr Formation in Ductile Materials
(The American Society of Mechanical Engineers (ASME), 2002)An analytical model for drilling burr formation was developed. The model holds for ductile materials that do not show catastrophic fracture during the plastic deformation of workpiece material ... -
Recent Developments in Gradient Plasticity—Part I: Formulation and Size Effects
(The American Society of Mechanical Engineers (ASME), 2002)The purpose of this two-part article, is first to give an update of recent developments of gradient plasticity as this was advanced by Aifantis and co-workers in the early eighties to address ... -
The Influence of Indenter Tip Radius on the Micro-Indentation Hardness
(The American Society of Mechanical Engineers (ASME), 2002)The micro-indentation experiments have shown that the indentation hardness depends not only on the indentation depth but also on the indenter tip radius. In fact, the indentation hardness displays ... -
A Nonlocal Phenomenological Anisotropic Finite Deformation Plasticity Model Accounting for Dislocation Defects
(The American Society of Mechanical Engineers (ASME), 2002)A phenomenological, polycrystalline version of a nonlocal crystal plasticity model is formulated. The presence of geometrically necessary dislocations (GNDs) at, or near, grain boundaries is modeled ... -
Analytical Solution of a Borehole Problem Using Strain Gradient Plasticity
(The American Society of Mechanical Engineers (ASME), 2002)An analytical solution is presented for the borehole problem of an elasto-plastic plane strain body containing a traction-free circular hole and subjected to uniform far field stress. A strain ... -
Mechanical Behavior of a Cu-Al-Be Shape Memory Alloy Under Multiaxial Proportional and Nonproportional Loadings
(The American Society of Mechanical Engineers (ASME), 2002)This paper is concerned with the mechanical behavior of a Cu-Al-Be Shape Memory Alloy (SMA). A large experimental database, made of tension-internal pressure tests and biaxial compressive tests, ...