Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1201-1220 of 3257
-
Evaluation of Thermal Aging Embrittlement in Directionally Solidified Ni-Base Superalloy by Small Punch Test
(The American Society of Mechanical Engineers (ASME), 2005)In order to develop a procedure for evaluating the degradation of impact toughness in directionally solidified Ni-base superalloy CM247LC, which is commonly used for advanced gas turbine blades, ... -
Foreword
(The American Society of Mechanical Engineers (ASME), 2004)There has been extensive research on carbon nanotubes since their first discovery in 1991. Carbon nanotubes display superior material properties, and have many potential applications in nano-electronics, ... -
A Study of Thermal Fracture in Functionally Graded Thermal Barrier Coatings Using a Cohesive Zone Model
(The American Society of Mechanical Engineers (ASME), 2004)This work describes the application of two-dimensional finite element models with a cohesive zone to study quasi-static crack extension in functionally graded Yttria stabilized Zirconia (YSZ)-Bond ... -
A Simplified Approach to Estimate Limiting Drawing Ratio and Maximum Drawing Load in Cup Drawing
(The American Society of Mechanical Engineers (ASME), 2004)A new and practically applicable equation, including the normal anisotropy R, the strain hardening exponent n, the friction coefficient μ, and the bending factor t0/rd for estimating the limiting ... -
Modeling of Fatigue Crack Propagation
(The American Society of Mechanical Engineers (ASME), 2004)Fatigue crack propagation was modeled by using the cyclic plasticity material properties and fatigue constants for crack initiation. The cyclic elastic-plastic stress-strain field near the crack ... -
Through-Thickness Residual Stress Distribution After the Cold Expansion of Fastener Holes and Its Effect on Fracturing
(The American Society of Mechanical Engineers (ASME), 2004)Many analytical and experimental techniques utilize two-dimensional analysis approach to determine residual strains and stresses at cold expanded holes. In the present work, a recently developed ... -
Influence of Extra Coarse Grains on the Creep Properties of 9 Percent CrMoV (P91) Steel Weldment
(The American Society of Mechanical Engineers (ASME), 2004)With modern welding methods, satisfactory microstructures in 9%CrMoV (P91) steel can be obtained with a modest variation in hardness and prior austenite grain size. However, there is always a ... -
Introduction of Compressive Residual Stress Using a Cavitating Jet in Air
(The American Society of Mechanical Engineers (ASME), 2004)Cavitation impact from a cavitation jet, which is formed from bubbles induced by a high-speed water jet in water, can be used for surface modification in a similar manner to shot peening. A ... -
Finite Element Evaluation of the Remaining Mechanical Strength of Deteriorated Cast Iron Pipes
(The American Society of Mechanical Engineers (ASME), 2004)The problem of deteriorating water pipes, resulting in leaks and breaks, affects municipalities worldwide. Corrosion appears to be a leading factor affecting pipe strength and service life. While ... -
Effect of Strain Path and the Magnitude of Prestrain on the Formability of a Low Carbon Steel: On the Textural and Microtextural Developments
(The American Society of Mechanical Engineers (ASME), 2004)A low carbon steel (0.07-wt % carbon) sheet metal was deformed in five different strain paths, from equi-biaxial tension to plane strain to near uniaxial tension, by in-plane stretching. Textural ... -
Size Effect on Flexural Strength of Fiber-Composite Laminates
(The American Society of Mechanical Engineers (ASME), 2004)The size effect on the flexural strength (or modulus of rupture) of fiber-polymer laminate beams failing at fracture initiation is analyzed. A generalized energetic-statistical size effect law ... -
Transverse-Isotropic Elastic and Viscoelastic Solids
(The American Society of Mechanical Engineers (ASME), 2004)A set of invariants are presented for transverse-isotropic materials whose gradients produce strain fields, instead of deformation fields as is typically the case. Finite-strain theories for elastic ... -
Observations of the Constitutive Response and Characterization of Filled Natural Rubber Under Monotonic and Cyclic Multiaxial Stress States
(The American Society of Mechanical Engineers (ASME), 2004)This work explores the monotonic and cyclic behaviors of filled, natural rubber. Results of stress-strain experiments conducted under stress states of simple, planar, and equibiaxial tension are ... -
Procedure for the Determination of True Stress-Strain Curves From Tensile Tests With Rectangular Cross-Section Specimens
(The American Society of Mechanical Engineers (ASME), 2004)The problem of determining true stress-strain curves from flat tensile specimens beyond the onset of necking has been investigated based on finite element analyses under consideration of experimental ... -
A Comparison of Two Self-Consistent Models to Predict the Cyclic Behavior of Polycrystals
(The American Society of Mechanical Engineers (ASME), 2004)Being of particular interest in this work, the effect of the interaction law on the predicted non-linear overall and local behaviors of FCC polycrystals of two well-established self-consistent ... -
A Two-Property Yield, Failure (Fracture) Criterion for Homogeneous, Isotropic Materials
(The American Society of Mechanical Engineers (ASME), 2004)A critical review is given of the various historical attempts to formulate a general, three-dimensional theory of failure for broad classes of homogeneous, isotropic elastic materials. Following ... -
Investigation of Fracture in Transparent Glass Fiber Reinforced Polymer Composites Using Photoelasticity
(The American Society of Mechanical Engineers (ASME), 2004)Fiber-reinforced plastic composite materials are being widely used in a variety of load bearing and high-performance structures. Reliable use and optimum design requires accurate methods for ... -
Influence of Carbon Content in Cobalt-Based Superalloys on Mechanical and Wear Properties
(The American Society of Mechanical Engineers (ASME), 2004)Two cobalt-based superalloys containing 1.6% and 2% carbon respectively were studied, with the emphasis on the influence of the carbon content on their microstructures, wear resistance, and ... -
Dynamic Compressive Behavior of EPDM Rubber Under Nearly Uniaxial Strain Conditions
(The American Society of Mechanical Engineers (ASME), 2004)Dynamic compressive stress-strain curves for ethylene-propylene-diene monomer (EPDM) rubber at various strain rates under nearly uniaxial strain conditions have been determined with a pulse-shaped ... -
Fatigue Crack Initiation Behavior of Welded AA5083 in a Seawater Environment
(The American Society of Mechanical Engineers (ASME), 2004)Aluminum Alloy 5083 is increasingly used in the ship building industry due to its excellent corrosion resistance and its favorable mechanical properties. A significant application of this alloy ...