Journal of Energy Resources Technology: Recent submissions
Now showing items 861-880 of 3450
-
Effects of Riser Diameter on Solids Holdup and Particle Velocity Profiles in Circulating Fluidized Bed Riser Systems
(The American Society of Mechanical Engineers (ASME), 2020)Tests were performed in a 0.1-m diameter small circulating fluidized bed (SCFB) and 0.3 m diameter cold flow circulating fluidized bed (CFCFB) riser systems located at the National Energy Technology Laboratory (NETL) to ... -
Measurement of Convective Heat Transfer Coefficients With Supercritical CO2 Using the Wilson-Plot Technique
(The American Society of Mechanical Engineers (ASME), 2020)This paper describes the measurement of convective heat transfer coefficients and friction factors for sCO2 flowing in a smooth tube and compares the results with published correlations for validation. The paper also ... -
Experimental Characterization of Two-Phase Flow Through Valves Applied to Liquid-Assisted Gas-Lift
(The American Society of Mechanical Engineers (ASME), 2020)Liquid-assisted gas-lift (LAGL) is a recently developed concept to unload wells using a gas–liquid fluid mixture. The success deployment of the LAGL technology is related to the behavior of two-phase flow through gas-lift ... -
Numerical Modeling of Coupled Fluid Flow and Geomechanical Stresses in a Petroleum Reservoir
(The American Society of Mechanical Engineers (ASME), 2020)A fully coupled hydro and geomechanical model has been used to predict the transient pressure disturbance, reservoir deformation, and effective stress distribution in both homogeneous and heterogeneous reservoirs. The ... -
Using an Integrated Multidimensional Scaling and Clustering Method to Reduce the Number of Scenarios Based on Flow-Unit Models Under Geological Uncertainties
(The American Society of Mechanical Engineers (ASME), 2020)Understanding the role of geological uncertainties on reservoir management decisions requires an ensemble of reservoir models that cover the uncertain space of parameters. However, in most cases, high computation time is ... -
Quantitative Evaluation on the Evolution of Water Cone Behavior in a Heavy Oil Reservoir With Bottom Water
(The American Society of Mechanical Engineers (ASME), 2020)In order to solve the problem of the unclear understanding of the water cone behavior and its influencing factors of horizontal well in a heavy oil reservoir with bottom water, in this paper, a series of physical models ... -
Wellbore Stability in Layered Rocks: A Comparative Study of Strength Criteria
(The American Society of Mechanical Engineers (ASME), 2020)Wellbore instability is a critical issue restricting efficient well drilling and successful development of oil and gas field. Most instability problems originate from shale formations because of their distinct laminated ... -
Estimation of the Bubble Influence on the Imbibed Liquid Measurement During Tight Rock Continuous Imbibition
(The American Society of Mechanical Engineers (ASME), 2020)Bubble influence makes the measured liquid content in rock become less during continuous imbibition because it attaches to the surface of the tight sand increasing the buoyancy of rock in liquid. The imbibition experiment ... -
Simulation of Cavity Extension Formation in the Early Ignition Stage Based on a Coal Block Gasification Experiment
(The American Society of Mechanical Engineers (ASME), 2020)Underground coal gasification (UCG) is a highly efficient new type of coal mining technology with broad future prospects. In order to study the cavity extension formation in the early ignition stage of UCG, a block coal ... -
Feasibility and Sensitivity Analysis of a Hybrid Photovoltaic/Wind/Biogas/Fuel-Cell/Diesel/Battery System for Off-Grid Rural Electrification Using homer
(The American Society of Mechanical Engineers (ASME), 2020)Integrating renewable energy technologies in a single system is becoming more reliable to meet electrical demand of remote locations. Here, integration and the optimal use of various available energy resources in a stand-alone ... -
Numerical Simulation of Natural Gas Pipeline Transients
(American Society of Mechanical Engineers (ASME), 2019)Simulations of natural gas pipeline transients provide an insight into a pipeline capacity to deliver gas to consumers or to accumulate gas from source wells during various abnormal conditions and under variable consumption ... -
Experimental Investigation of the Effect of Shale Anisotropy Orientation on the Main Drilling Parameters Influencing Oriented Drilling Performance in Shale
(American Society of Mechanical Engineers (ASME), 2019)The influence of shale anisotropy and orientation on shale drilling performance was studied with an instrumented laboratory drilling rig with a 38.1-mm dual-cutter polycrystalline diamond compact (PDC) bit, operating at a ... -
Investigation of A Low Emission Liquid Fueled Reverse-Cross-Flow Combustor
(American Society of Mechanical Engineers (ASME), 2019)The investigated combustor employs injection of liquid fuel (ethanol) into the strong cross-flow of air using a round tube to achieve effective fuel atomization in non-premixed mode of operation. The reverse-flow configuration ... -
Adaptation of Methanol–Dodecanol–Diesel Blend in Diesel Genset Engine
(American Society of Mechanical Engineers (ASME), 2019)Miscibility of methanol in mineral diesel and stability of methanol–diesel blends are the main obstacles faced in the utilization of methanol in compression ignition engines. In this experimental study, combustion, ... -
Energy- and Exergy-Based Analysis for Reducing Energy Demand in Heat Processes for Aluminum Casting
(American Society of Mechanical Engineers (ASME), 2019)In this paper, energy- and exergy-based analysis is used to analyze a factory with high energy demand for the production of aluminum discs. The analysis is focused on heat processes that take place in a melting furnace, a ... -
Experimental and Numerical Evaluation of Water Control and Production Increase in a Tight Gas Formation With Polymer
(American Society of Mechanical Engineers (ASME), 2019)An integrated technique has been developed to experimentally and numerically evaluate water control and production increase in a tight gas formation with polymer. Experimentally, polymer has been appropriately selected and ... -
Design Performance Simulation of a Supercritical CO2 Cycle Coupling With a Steam Cycle for Gas Turbine Waste Heat Recovery
(American Society of Mechanical Engineers (ASME), 2019)This study presents a train of thought and method for flue gas energy utilization management by connecting an optimized supercritical carbon dioxide (S-CO2) Brayton cycle with a selected steam/water Rankine cycle to recover ... -
Prediction of Cyclic Variability and Knock-Limited Spark Advance in a Spark-Ignition Engine
(American Society of Mechanical Engineers (ASME), 2019)Engine knock remains one of the major barriers to further improve the thermal efficiency of spark-ignition (SI) engines. SI engine is usually operated at knock-limited spark advance (KLSA) to achieve possibly maximum ... -
Numerical Study of a Flow Field Near the Bit for a Coiled-Tubing Partial Underbalanced Drilling Method
(American Society of Mechanical Engineers (ASME), 2019)A new drilling method called coiled-tubing partial underbalanced drilling (CT-PUBD) was proposed in this paper. The method is not only able to enhance rate of penetration (ROP) just like the conventional underbalanced ... -
Mitigation of Annulus Pressure Buildup in Offshore Gas Wells by Determination of Top of Cement
(American Society of Mechanical Engineers (ASME), 2019)Annulus pressure buildup (APB) is still a serious problem in offshore gas wells, which threatens the safety of wells for the entire phases of drilling, completion, and production. The existing methods for mitigating APB ...