Now showing items 3361-3380 of 3450

    • A Technical Evaluation of Modular Incinerators With Heat Recovery 

      R. E. Frounfelker; N. J. Kleinhenz (The American Society of Mechanical Engineers (ASME), 1981)
      The use of small modular incinerator systems for solid waste disposal and energy recovery in municipal and industrial applications is studied. The technical evaluation presented herein is based ...
    • State-of-the-Art of Models for Geothermal Recovery Processes 

      C. F. Tsang; J. S. Y. Wang (The American Society of Mechanical Engineers (ASME), 1981)
      Recent interest in geothermal energy development has contributed to the advance in the modeling of nonisothermal flows, especially of the two-phase, steam-water phenomena. In this paper, the key ...
    • Modeling Capabilities for the Devonian Gas Shales 

      F. Kucuk; W. K. Sawyer; J. Alam (The American Society of Mechanical Engineers (ASME), 1981)
      Mathematical models for predicting gas performance of Devonian gas shale reservoirs can be divided into two groups: single and dual porosity models. Further, two dual porosity models have been ...
    • Technical Editor’s Page 

      J. B. Cheatham (The American Society of Mechanical Engineers (ASME), 1980)
    • Submerged Production System—A Final Report 

      J. A. Burkhardt; T. W. Childers; R. E. Anderson; W. D. Loth; T. W. Michie (The American Society of Mechanical Engineers (ASME), 1980)
      The offshore pilot test of Exxon’s Submerged Production System (SPS) has reached a successful conclusion. This pilot test encompassed the entire spectrum of SPS equipment, spanning from the well ...
    • Bending of Tubular Bundles Attached to Marine Risers 

      T. Huang; D. W. Dareing; W. T. Beran (The American Society of Mechanical Engineers (ASME), 1980)
      Individual tubulars attached to marine risers are modelled as continuous axially loaded multiple-spanned beams. Traditional methods for solving continuous beam-column problems require the solution ...
    • Permafrost Beneath the Beaufort Sea: Near Prudhoe Bay, Alaska 

      P. V. Sellmann; E. J. Chamberlain (The American Society of Mechanical Engineers (ASME), 1980)
      The occurrence and properties of subsea permafrost near Prudhoe Bay, Alaska, were investigated by drilling and probing. Nine holes were drilled and 27 sites were probed with a cone penetrometer. ...
    • Design of Hydrostatically Supported Sand Islands for Arctic Drilling 

      B. E. W. Dowse (The American Society of Mechanical Engineers (ASME), 1980)
      The search for oil and gas has already extended to the Arctic areas of the world. To date conventional sand islands have been used for exploration drilling purposes in water depths of up ...
    • High and Low-Cycle Fatigue Behavior of Prestressed Concrete in Offshore Structures 

      B. C. Gerwick; W. J. Venuti (The American Society of Mechanical Engineers (ASME), 1980)
      The expanding use of prestressed concrete in offshore structures, both fixed and floating, in ever more hostile environments has generated intense interest in its fatigue endurance capabilities, ...
    • Technical Editor’s Page 

      John B. Cheatham (The American Society of Mechanical Engineers (ASME), 1980)
    • Technical Editor’s Page 

      J. B. Cheatham (The American Society of Mechanical Engineers (ASME), 1980)
    • Effects of AlCl3 Additive on Cutting Forces and Diamond Wear Rate While Cutting Granite With a Single Diamond 

      F. C. Appl; B. N. Rao; B. H. Walker (The American Society of Mechanical Engineers (ASME), 1980)
      The effects of surfactant solution aluminum chloride on cutting granite rock with a diamond were investigated experimentally. Tests were conducted by cutting on the cylindrical surface of a ...
    • Conversion of Refuse to Electrical Energy at the St. Louis-Union Electric Refuse Fuel Demonstration Project 

      D. E. Fiscus; C. C. Wiles; P. G. Gorman (The American Society of Mechanical Engineers (ASME), 1980)
      At the Union Electric Meramec power plant in St. Louis, tests in which refuse-derived fuel was co-fired with pulverized coal in a tangential suspension-fired coal boiler have been conducted. ...
    • Theoretical and Experimental Research on Hydraulic Fracturing 

      M. E. Hanson; G. D. Anderson; R. J. Shaffer (The American Society of Mechanical Engineers (ASME), 1980)
      We are conducting a joint theoretical/experimental research program on hydraulic fracturing. Newly developed two-dimensional numerical models (which include complete descriptions of the elastic ...
    • Fracture Azimuth—A Shallow Experiment 

      M. B. Smith; J. M. Logan; M. D. Wood (The American Society of Mechanical Engineers (ASME), 1980)
      A small-scale, shallow experiment was conducted by Amoco Production Research, Sandia Laboratories, and the U. S. Geological Survey, in order to study the potential of several geophysical monitoring ...
    • Thermodynamic and Economic Analysis of Heat Pumps for Energy Recovery in Industrial Processes 

      A. H. Urdaneta-B; P. S. Schmidt (The American Society of Mechanical Engineers (ASME), 1980)
      A computer code has been developed for analyzing the thermodynamic performance, cost and economic return for heat pump applications in industrial heat recovery. Starting with basic defining ...
    • Dynamics of Suspended Marine Pipelines 

      J. E. Hall; A. J. Healey (The American Society of Mechanical Engineers (ASME), 1980)
      As the development of offshore oil and gas production proceeds, the dynamic stresses in pipelines induced by laying operations become more important. The contribution of this paper is to the ...
    • Mooring with Multicomponent Cable Systems 

      K. A. Ansari (The American Society of Mechanical Engineers (ASME), 1980)
      Relative to the present-day need for offshore operations involving the use of moored vessels, mooring system design has become quite complex. Since a proper choice of mooring line components ...
    • Selection and Sizing of Velocity-Actuated Subsurface Safety Valves 

      H. D. Beggs; E. A. Proaño; C. E. Roman-Lazo; J. P. Brill (The American Society of Mechanical Engineers (ASME), 1980)
      Subsurface safety valves (SSSVs) are installed in offshore oil and gas wells to shut in the wells in case of pressure loss at the wellhead. The selection of these SSSVs requires prediction ...