Journal of Energy Resources Technology: Recent submissions
Now showing items 3061-3080 of 3450
-
Wave-Island Interactions About Circular Artificial Islands
(The American Society of Mechanical Engineers (ASME), 1984)The behavior of waves interacting with islands has gained renewed interest with the construction of exploratory drilling islands in the Arctic. This paper focuses upon the behavior of waves ... -
Investigation of API 8 Round Casing Connection Performance—Part I: Introduction and Method of Analysis
(The American Society of Mechanical Engineers (ASME), 1984)The purpose of this investigation was to gain a better understanding into the mechanical behavior of the API 8 Round casing connection, when subjected to service loads of assembly interference, ... -
A Reconnaissance Study of the Hydrothermal Characteristics of Pilgrim Springs, Alaska
(The American Society of Mechanical Engineers (ASME), 1984)A reconnaissance level study of the Pilgrim Springs geothermal system was conducted to determine the near-surface thermal regime and to obtain information on the ground water flow regime within ... -
Stability Considerations for Existing Conventional Autopilots on Modern Ship Types
(The American Society of Mechanical Engineers (ASME), 1984)The directional stability of three modern ship types with conventional nonadaptive autopilots is examined. It is shown that while attempting to improve the course-keeping ability of these ships, ... -
Ice Action on Two Cylindrical Structures
(The American Society of Mechanical Engineers (ASME), 1984)Ice action on two cylindrical structures, located side by side, has been investigated in a small-scale experimental study to determine the interference effects on the ice forces generated during ... -
Initiation of Propagating Buckles From Local Pipeline Damages
(The American Society of Mechanical Engineers (ASME), 1984)The paper deals with the subject of initiation of a propagating buckle in an offshore pipeline. If the external pressure is high enough, then a propagating buckle can be initiated by locally ... -
Shear Fracture Arrestability of Controlled Rolled Steel X70 Line Pipe by Full-Scale Burst Test
(The American Society of Mechanical Engineers (ASME), 1984)The High Strength Line Pipe Research Committee organized by the Iron and Steel Institute of Japan has conducted five full-scale burst tests on line pipe of 48 in. o.d. × 0.720 in. w.t. ... -
Solutions for Small Slope Pipeline Lifting Problems
(The American Society of Mechanical Engineers (ASME), 1984)Two classes of submarine pipeline handling problems are considered, namely the lifting of a pipe with a free end for tie-in purposes, and the raising of part of a continuous line for hot-tapping ... -
Dynamic Motions of Marine Pipelines on the Ocean Bottom
(The American Society of Mechanical Engineers (ASME), 1984)This paper describes a dynamic model of a pipeline portion exposed to wave and current forces for the purpose of assessing on bottom stability. When an exposed span is marginally stable, and ... -
The Influence of Boundary Layer Velocity Gradients and Bed Proximity on Vortex Shedding From Free Spanning Pipelines
(The American Society of Mechanical Engineers (ASME), 1984)The paper summarizes the results of a laboratory study of the separate and combined effects of bed proximity and large velocity gradients on the frequency of vortex shedding from pipeline spans ... -
Freezing of a Semi-Infinite Medium With Initial Temperature Gradient
(The American Society of Mechanical Engineers (ASME), 1984)Exact solutions to problems of conductive heat transfer with solidification are rare due to the nonlinearity of the equations. The heat balance integral technique is used to obtain an approximate ... -
Investigation of the Alexander L. Kielland Failure—Metallurgical and Fracture Analysis
(The American Society of Mechanical Engineers (ASME), 1984)On March 27, 1980, the semi-submersible platform Alexander L. Kielland broke down in a storm in the North sea, resulting in a loss of 123 lives. The investigation subsequently performed by ... -
The Influence of Tension, Pressure and Weight on Pipe and Riser Deformations and Stresses
(The American Society of Mechanical Engineers (ASME), 1984)The influence of tension, pressure, and weight on different aspects of pipe and riser behavior has already been the subject of many articles (see references). In spite of this it has frequently ... -
Ocean and Arctic Engineering: Risk and the Economic, Social, Legal Context
(The American Society of Mechanical Engineers (ASME), 1984)Ocean and arctic engineers typically play three roles. Through research, they contribute new understandings of basic scientific principles applied in a strenuous and hostile environment. Through ... -
Stiffness and Energy Dissipation Characteristics of Guyed Tower With Dynamic Mooring Properties
(The American Society of Mechanical Engineers (ASME), 1984)A simple model for a complex system is presented that contains the essential properties of the guyed tower. The dynamic response to wave load of a guyed tower is represented by a single ... -
The Stress Analysis and Experimental Research of Tubular Joints of Offshore Drilling Platform
(The American Society of Mechanical Engineers (ASME), 1984)An analytical method for the stress analysis of tubular joints of T, Y, K type is presented in this paper. The stress distribution and stress concentration factor of the joints are calculated. ... -
Damage Detection in Offshore Structures by the Random Decrement Technique
(The American Society of Mechanical Engineers (ASME), 1984)The Random Decrement Technique has shown promise as an inspection technique for offshore structures. The major advantage of this technique is that it requires only measurements of the dynamic ... -
Structural Response Analysis of Tension Leg Platforms
(The American Society of Mechanical Engineers (ASME), 1984)A linear response analysis method of the tension leg platform (TLP) subjected to regular waves is proposed. In this analysis method, flexibility of the superstructure can be taken into account ... -
Selection and Evaluation of High-Strength Steel for Hutton TLP Tension Leg Elements
(The American Society of Mechanical Engineers (ASME), 1984)The development of the tension leg platform (TLP) for the Hutton Field in the North Sea represents the first application of this deepwater concept. The use of vertical tension legs as the ... -
Cavitating and Structured Jets for Mechanical Bits to Increase Drilling Rate—Part I: Theory and Concepts
(The American Society of Mechanical Engineers (ASME), 1984)The erosion and cleaning effect of jets is enhanced when the degree of cavitation on or near the bottom of the hole is increased. Analyses indicate that self-excited, acoustically resonating ...