Journal of Energy Resources Technology: Recent submissions
Now showing items 2741-2760 of 3450
-
Nonlinear Behavior of Plain Woven G. F. R. P. Under Repeated Biaxial Tension/Torsion Loading
(The American Society of Mechanical Engineers (ASME), 1991)Fatigue tests on a plain woven glass composite at room temperature under biaxial (tension/torsion) loading were conducted. Nonlinear stress-strain (S-S) response especially in shear, was found and ... -
Local Stress Distribution in the Vicinity of Loading Points in Flexural Test of Orthotropic Beams
(The American Society of Mechanical Engineers (ASME), 1991)The two-dimensional stress distributions in orthotopic composite beam under 4-point flexure are analyzed by replacing the concentrated load by distributing pressure in the vicinity of loading nose ... -
Stochastic Models Related to Fatigue Damage of Materials
(The American Society of Mechanical Engineers (ASME), 1991)The stochastic models for the fatigue damage phenomena are proposed. They describe the uncertainty caused by inhomogeneity of materials for fatigue crack propagation of metals and fatigue damage ... -
A Comparison of the Dynamic Transient Anti-Plane Shear Crack Energy Release Rate for Standard Linear Solid and Power-Law-Type Viscoelastic Materials
(The American Society of Mechanical Engineers (ASME), 1991)The problem of a semi-infinite mode III crack that suddenly begins to propagate at a constant speed is considered for a general linear viscoelastic body. It is shown that the results of an ... -
A Numerical Comparison of Current Mathematical Models of Twisted Wire Cables Under Axisymmetric Loads
(The American Society of Mechanical Engineers (ASME), 1991)Several mathematical models are currently available to predict the mechanical behavior of twisted wire cables and ACSR electrical conductors subjected to axisymmetric loads. The equations for each ... -
Localized Deformation Using Higher Order Stress/Strain Theory
(The American Society of Mechanical Engineers (ASME), 1990)A material is considered which consists of rough interacting blocks. The interaction, which is expressed in terms of the ratio of the normal and tangential force at the contact points of the ... -
Self-Excited Vibrations Induced by Drag Bits
(The American Society of Mechanical Engineers (ASME), 1990)Drillstring vibrations cause premature failure of downhole tools and the drillstring itself. Also, drill bits do not drill efficiently as a result of these vibrations and this inefficiency causes ... -
Friction Gages for In-Situ Rock-Mass Deformability and Stress Measurements
(The American Society of Mechanical Engineers (ASME), 1990)The in-situ deformability of rocks and the state-of-stress must be known for the analysis and design of surface and underground structures. This paper presents a method for determining the ... -
Ramp Wave Analysis of the Solid/Vapor Heat Pump
(The American Society of Mechanical Engineers (ASME), 1990)A theramlly driven heat pump using a solid/vapor adsorption/desorption compression process in a vapor compression cycle is thermodynamically analyzed. The cycle utilizes a simple heat transfer ... -
Wall Contact Forces on Helically Buckled Tubulars in Inclined Wells
(The American Society of Mechanical Engineers (ASME), 1990)Wall forces on helically buckled pipe can cause large frictional forces that may prevent movement of the pipe in steeply inclined holes. A method of analyzing the dependency of the wall contact ... -
Thermo-Fluid Dynamic Design Study of Single and Double-Inflow Radial and Single-Stage Axial Steam Turbines for Open-Cycle Thermal Energy Conversion Net Power-Producing Experiment Facility in Hawaii
(The American Society of Mechanical Engineers (ASME), 1990)The results of the study of the optimum thermo-fluid dynamic design concept are presented for turbine units operating within the open-cycle ocean thermal energy conversion (OC-OTEC) systems. The ... -
Studying Transient Multi-Phase Flow Using the Pipeline Analysis Code (PLAC)
(The American Society of Mechanical Engineers (ASME), 1990)The Pipeline Analysis Code, PLAC, is utilized to study the flow generated from a shallow dip in a long pipeline. It shows that much longer and infrequent slugs are formed when liquid is ... -
Experimental Study of Micronized Coal/Water Slurry Rheology at High Shear Rates
(The American Society of Mechanical Engineers (ASME), 1990)The rheological behavior of four micronized coal water slurry (CWS) samples was studied experimentally for a wide range of shear rates between 3 and 30,000 s−1 . The systematic rheological ... -
Performance and Emissions of a Diesel Engine Using a Coal-Derived Fuel
(The American Society of Mechanical Engineers (ASME), 1990)A coal-derived synthetic fuel was blended with a control diesel fuel and then tested in a single-cylinder, direct-injected, diesel engine. Comparisons of the blended fuel to the control Diesel ... -
Breakdown of the Exergy Balance in a Glass Furnace
(The American Society of Mechanical Engineers (ASME), 1990)An exergy balance for an industrial glass furnace was constructed on the basis of measured thermodynamic variables. The experimental data were collected for different operating modes, especially ... -
Second Law Analysis of Spray Evaporation
(The American Society of Mechanical Engineers (ASME), 1990)A second law analysis has been developed for an evaporative atomized spray in a uniform parallel stream of hot gas. Using a discrete droplet evaporation model, an equation for entropy balance ... -
Development of a 16-MWth Coal-Water/Heavy Oil Burner for Front-Wall Firing
(The American Society of Mechanical Engineers (ASME), 1990)The Canadian program of coal-water fuel (CWF) technology development has included the demonstration of “commercial” burners for CWF in both coal and oil-designed utility boilers. The demonstrations ... -
Strain Hardening in Salt—Results of the SALMON Experiment
(The American Society of Mechanical Engineers (ASME), 1990)SALMON was a nuclear explosion in the Tatum salt dome, near Hattiesburg, Mississippi, that took place on October 22, 1964. Computational attempts to simulate the experimental results had been ... -
Dynamic Response of Thin-Walled Composite Material Timoshenko Beams
(The American Society of Mechanical Engineers (ASME), 1990)Thin-walled structural members are used extensively in the offshore industry in applications ranging from marine risers to platforms and frames. Advanced fiber composite structural members may ... -
Three-Dimensional Modeling of Hydraulic Fractures in Layered Media: Part I—Finite Element Formulations
(The American Society of Mechanical Engineers (ASME), 1990)A comprehensive model represented by a set of equations governing the mechanics of planar hydraulic fracture propagation in a multi-layered reservoir is presented. A general-purpose integral ...