Journal of Energy Resources Technology: Recent submissions
Now showing items 2681-2700 of 3450
-
Off-Diagonal Elastic Constants and Anisotropic Damage
(The American Society of Mechanical Engineers (ASME), 1992)Various anisotropic damage models are investigated to take into account the nonlinear behavior of a ceramic matrix composite. A critical analysis of classical strain metrology results proves that ... -
The Optimum Design of Stratified Thermal Energy Storage Systems—Part I: Development of the Basic Analytical Model
(The American Society of Mechanical Engineers (ASME), 1992)This investigation employs the techniques of second law analysis to show that significant improvements in performance are possible through the use of “perfectly stratified” thermal energy storage ... -
Pleasant Bayou Geopressured-Geothermal Reservoir Analysis—October 1991
(The American Society of Mechanical Engineers (ASME), 1992)Many sedimentary basins contain formations with pore fluids at pressures higher than hydrostatic value; these formations are called geopressured. The pore pressure is generally well in excess of ... -
Development of New PDC Bits for Drilling of Geothermal Wells—Part 1: Laboratory Testing
(The American Society of Mechanical Engineers (ASME), 1992)Rock cutting, drilling and durability tests were conducted in order to obtain data to design polycrystalline diamond compact (PDC) bits for geothermal well drilling. Both conventional and new ... -
Thermal Stresses Under Engine Heat Flux—Part 2: Thin Metallic Films on Ceramic Coatings
(The American Society of Mechanical Engineers (ASME), 1992)The thermal stresses in a metallic thin film bonded to a ceramic coating on a metal substrate, generated by heat flux conditions in an engine, were studied. The film yields as a result of ... -
Simulation Study of the Matsukawa Geothermal Reservoir: Natural State and Its Response to Exploitation
(The American Society of Mechanical Engineers (ASME), 1992)A numerical simulation study on the natural state of the Matsukawa, Japan geothermal reservoir was carried out with a simplified two-dimensional cross-sectional model. The results agreed reasonably ... -
Wind Evaporator Heat Pumps—Part II: Thermal Performance Results
(The American Society of Mechanical Engineers (ASME), 1992)Wind evaporators are alternative evaporators for air source heat pumps which rely on wind-driven or natural convection to move air across the heat transfer surfaces. A fully automatic, ... -
Thermal Stresses Under Engine Heat Flux—Part 1: Ceramic Coating on Metal Substrate
(The American Society of Mechanical Engineers (ASME), 1992)The thermal stresses in a ceramic coating bonded to a metal substrate generated by heat flux conditions in an engine were studied. Edge delamination of the coating was related to the displacements ... -
Analytical Approach to Selecting and Designing a Miniature Downhole Refrigerator
(The American Society of Mechanical Engineers (ASME), 1992)The design approach and results from a series of analyses used to select a miniature high-temperature multi-watt refrigerator for thermally protecting downhole instruments are described. Thirty-one ... -
Computer Modeling of the Continuous Annealing Furnace
(The American Society of Mechanical Engineers (ASME), 1992)A computer program to calculate the strip temperature heated in the continuous annealing furnace was developed, using the zone method for radiative heat transfer analysis with the measured gas ... -
Effect of Drag Forces on Bit Weight in High-Curvature Well Bores
(The American Society of Mechanical Engineers (ASME), 1992)This paper gives a method of analysis for determining drill string weight required to develop a given bit force while drilling through and out of high-curvature well bores. The analysis is ... -
Development of New PDC Bits for Drilling of Geothermal Wells—Part 2: Field Testing
(The American Society of Mechanical Engineers (ASME), 1992)In order to develop polycrystalline diamond compact (PDC) bits of about 8-1/2 in. in diameter which are able to drill geothermal wells, we have conducted the investigation with respect to the ... -
The Thermal Performance of the Cross-Flow Three-Dimensional Flat Plate Indirect Evaporative Cooler
(The American Society of Mechanical Engineers (ASME), 1992)Evaporative coolers consist of two main types: (a) the direct evaporative cooler in which water mixes with the air to be cooled; and (b) the indirect evaporative cooler in which water is ... -
Formation of Flammable Zones Due to the Action of Diffusional Mass Transfer—A Simplified Approach
(The American Society of Mechanical Engineers (ASME), 1992)The transient concentration profiles of a fuel or a toxic gas were examined following its release into air within a long confined volume with either an open or a closed end. The exact ... -
A Method for Improving the Quality of Bituminous Froth From Water Extraction of Oil Sands
(The American Society of Mechanical Engineers (ASME), 1992)Bituminous froths produced from the water extraction of oil sands contain significant quantities of sand and water which must be removed prior to upgrading the bitumen to synthetic crude oil. ... -
Wind Evaporator Heat Pumps—Part I: Test Methods
(The American Society of Mechanical Engineers (ASME), 1992)Wind evaporators are alternative evaporators for air source heat pumps which rely on wind-driven or natural convection to move air across the heat transfer surfaces. It is believed that, in ... -
An Experimental Investigation of the Transport and Combustion Processes Within Fractured Oil Sand Beds
(The American Society of Mechanical Engineers (ASME), 1992)The behavior of fractured beds of light oil (37° API) sand cores when subjected to high-temperature, low-velocity vitiated air stream of the combustion products of near-lean flammability ... -
Investigation of a Composite Tubing Connection Performance
(The American Society of Mechanical Engineers (ASME), 1991)The purpose of this study is the understanding of the mechanical behavior of a threaded tubing connection made out of composite materials. The threaded tubing connection has been calculated ... -
Fracture of an Orthotropic Strip Containing a Pair of Coplanar Cracks Perpendicular to the Edges of the Strip
(The American Society of Mechanical Engineers (ASME), 1991)The problem of an infinitely long orthotropic strip containing a pair of coplanar cracks perpendicular to the edges of the strip is studied. The surfaces of the cracks are loaded by an ... -
Elastic-Plastic Compaction of Geopressured Sandstone
(The American Society of Mechanical Engineers (ASME), 1991)The economic development of United States Gulf Coast geopressured-geothermal energy resources depends in part upon an improved understanding of reservoir rock response to long-term aquifer production. ...