Journal of Energy Resources Technology: Recent submissions
Now showing items 2541-2560 of 3450
-
Buckling and Lockup of Tubulars in Inclined Wellbores
(The American Society of Mechanical Engineers (ASME), 1995)This paper studies sinusoidal and helical buckling of tubulars in inclined wellbores and the “lockup” of tubulars due to buckling. The results show that tubular buckling starts from the tubular ... -
High-Power Multi-Stage Rankine Cycles
(The American Society of Mechanical Engineers (ASME), 1995)This paper presents an analysis of the multi-stage Rankine cycle aiming at optimizing the power output from low-temperature heat sources such as geothermal or waste heat. A design methodology ... -
Modeling of Roller Cone Bit Lift-Off Dynamics in Rotary Drilling
(The American Society of Mechanical Engineers (ASME), 1995)Rotary drilling with roller cone bit is often accompanied by wide fluctuations of the weight on bit (WOB). In certain cases, the WOB periodically reduces to null. It has been postulated that ... -
An Operation Support System of Large City Gas Networks Based on Fluid Transient Model
(The American Society of Mechanical Engineers (ASME), 1995)This paper describes the essential features and experience of applying a fluid transient model to the operation support system of large city gas pipeline networks. The system, operating in the ... -
NOx Emissions From a Diesel Engine Fueled With Natural Gas
(The American Society of Mechanical Engineers (ASME), 1995)The performance and emission characteristics of a single-cylinder two-stroke diesel engine fueled with direct injection of natural gas entrained with pilot diesel ignition enhancer have been ... -
End Effects in Laminated Anisotropic Beams—Part II
(The American Society of Mechanical Engineers (ASME), 1995)An analytical method of examining the stress field near the edge of a simply supported, laminated beam was developed in Part I of this paper. The result was a system of second-order, ordinary, ... -
An Experimental Study of the Drilling of Aramid Composites
(The American Society of Mechanical Engineers (ASME), 1995)Major drilling characteristics of Aramid fiber-reinforced plastics are experimentally investigated. The chip appears highly deformed and tends to smear on the tool. Forces and, mainly, torque are ... -
Unsteady Forced Convection Heat Transfer From a Translating and Spinning Body
(The American Society of Mechanical Engineers (ASME), 1995) -
A Biomass Combustion-Gasification Model: Validation and Sensitivity Analysis
(The American Society of Mechanical Engineers (ASME), 1995)The aim of the present paper is to study the gasification and combustion of biomass and waste materials. A model for the analysis of the chemical kinetics of gasification and combustion ... -
The San Andreas Fault Zone Drilling Project: Scientific Objectives and Technological Challenges
(The American Society of Mechanical Engineers (ASME), 1995)We are leading a new international initiative to conduct scientific drilling within the San Andreas fault zone at depths of up to 10 km. This project is motivated by the need to understand ... -
End Effects in Laminated Anisotropic Beams — Part I
(The American Society of Mechanical Engineers (ASME), 1995)The derivation of an analytical method to examine the stress field near the end of a simply supported, laminated beam is presented. Specific effort has been directed to accurately calculate ... -
Optimal Second-Law Efficiency for a Brayton Cycle With an Internal Heat Source
(The American Society of Mechanical Engineers (ASME), 1995)Net work of an endoreversible Brayton cycle and its second-law efficiency are examined for a heat source (hot air) that is initially at a temperature typical of adiabatic and stoichiometric ... -
Optimal Operational Planning of Cogeneration Systems With Thermal Storage by the Decomposition Method
(The American Society of Mechanical Engineers (ASME), 1995)An optimal operational planning method is proposed for cogeneration systems with thermal storage. The daily operational strategy of constituent equipment is determined so as to minimize the daily ... -
Full-Fuel-Cycle Modeling for Alternative Transportation Fuels
(The American Society of Mechanical Engineers (ASME), 1995)Utilization of alternative fuels in the transportation sector has been identified as a potential method for mitigation of petroleum-based energy dependence and pollutant emissions from mobile ... -
Prediction of Solid Oxide Fuel Cell Power System Performance Through Multi-Level Modeling
(The American Society of Mechanical Engineers (ASME), 1995)This paper presents an integrated multi-level model of a solid oxide fuel cell system, which accounts for the effects of concentration, activation, and ohmic polarizations on single-cell performance, ... -
Influences of Near-Wall and Induced Irrotational Motion in a Turbulent Boundary Layer on Wall Pressure Fluctuations
(The American Society of Mechanical Engineers (ASME), 1995)While many studies have investigated the influence of flow structure in a turbulent boundary layer on the wall pressure signature, the conclusions of these studies have often been limited due ... -
Optimum Efficiencies and Phase Change Temperatures in Latent Heat Storage Systems
(The American Society of Mechanical Engineers (ASME), 1994)This paper presents an analysis of a class of latent heat storage systems (LHSS). The analysis is based on a lumped model (the basic model) that allows a broad class of LHSSs to be completely ... -
Optimal Operation of a Cogeneration Plant in Combination With Electric Heat Pumps
(The American Society of Mechanical Engineers (ASME), 1994)An operational problem is discussed for a gas turbine cogeneration plant in combination with a heat pump/thermal storage system that utilizes time-of-use pricing of the electrical utility. An ... -
Prediction of Wear and Stresses While Drilling Through a Riser Flex Joint
(The American Society of Mechanical Engineers (ASME), 1994)Flex joints in risers introduce abrupt directional changes along the drillstring. High drillstring stresses and flex joint wear rates are introduced, particularly when the drillstring tension is ... -
An Experimental Investigation of Pure-Substance, Adiabatic Two-Phase Flow in a Vertical Pipe
(The American Society of Mechanical Engineers (ASME), 1994)Measurements of pressure drop, temperture, and average void fraction are presented for adiabatic, vertical-upwards, two-phase flow of Refrigerant 114 in a pipe. An experimental method has been ...