Journal of Energy Resources Technology: Recent submissions
Now showing items 2081-2100 of 3450
-
Surfactant-Enhanced Treatment of Oil-Based Drill Cuttings
(The American Society of Mechanical Engineers (ASME), 2005)Surfactant-enhanced washing of oil-based drill cuttings was evaluated as a technology of benefit to domestic oil producers. Laboratory studies showed the branched C14-C15 alcohol propoxylate sulfate ... -
Performance Characteristics of Regenerative Flow Compressors for Natural Gas Compression Application
(The American Society of Mechanical Engineers (ASME), 2005)In this paper we discuss the application of regenerative flow compressors (RFC) for low-pressure natural gas compression required by microturbine systems. A brief overview of fundamentals and the ... -
Theoretical Model of Borehole Heat Exchanger
(The American Society of Mechanical Engineers (ASME), 2005)The paper deals with the possible use of existing oil wells for geothermal energy production. A mathematical model, describing the process of exploitation of a borehole heat exchanger, has been ... -
Influence of Liquid Viscosity on the Pressure Loss and the Effectiveness of Drag-Reducing Agents in Horizontal Slug Flow
(The American Society of Mechanical Engineers (ASME), 2005)Measurements of drag reduction in two-phase oil-gas slug flow are presented in this study. Two types of oil with markedly different viscosities were examined in 10-cm inner diameter horizontal ... -
Microemulsion Additives Enable Optimized Formation Damage Repair and Prevention
(The American Society of Mechanical Engineers (ASME), 2005)A new microemulsion additive has been developed that is effective in remediating damaged wells and is highly effective in fluid recovery and relative permeability enhancement when applied in ... -
Effects of Several Major Irreversibilities on the Thermodynamic Performance of a Regenerative MHD Power Cycle
(The American Society of Mechanical Engineers (ASME), 2005)This communication presents the thermodynamic analysis along with a detailed parametric study of an irreversible regenerative MHD power cycle. The power output is adopted as the objective function ... -
Thermoeconomic Optimization of a LiBr/H2O Absorption Chiller Using Structural Method
(The American Society of Mechanical Engineers (ASME), 2005)The optimization strategy for absorption chiller systems is generally based on thermodynamic analysis. However, the optimum, so obtained, does not always guarantee the economic optimum. In this ... -
The Case for Hydrogen in a Carbon Constrained World
(The American Society of Mechanical Engineers (ASME), 2005)Unlike other fuels, hydrogen (H2) can be generated and consumed without generating carbon dioxide (CO2). This creates both significant engineering challenges and unsurpassed ecological advantages ... -
Effect of Cell Geometry on the Freezing and Melting Processes inside a Thermal Energy Storage Cell
(The American Society of Mechanical Engineers (ASME), 2005)This paper presents an analysis of the charge and discharge processes in a latent thermal energy storage cell. An individual cell is analyzed to study how its behavior affects the performance ... -
Underground Gas Storage Inventory Analysis by a Noniterative Method
(The American Society of Mechanical Engineers (ASME), 2005)Underground gas storage inventory and conditions are predicted using a practical model and a noniterative solution algorithm. Various simulation scenarios concerning underground gas storage in ... -
Damage Tolerance of Well-Completion and Stimulation Techniques in Coalbed Methane Reservoirs
(The American Society of Mechanical Engineers (ASME), 2005)Coalbed methane (CBM) reservoirs are characterized as naturally fractured, dual porosity, low permeability, and water saturated gas reservoirs. Initially, the gas, water, and coal are at thermodynamic ... -
Fine-Scale Simulation of Sandstone Acidizing
(The American Society of Mechanical Engineers (ASME), 2005)We have developed a fine-scale model of the sandstone core acid flooding process by solving acid and mineral balance equations for a fully three-dimensional flow field that changed as acidizing ... -
Organic Working Fluids for a Combined Power and Cooling Cycle
(The American Society of Mechanical Engineers (ASME), 2005)A new thermodynamic cycle has been developed for the simultaneous production of power and cooling from low-temperature heat sources. The proposed cycle combines the Rankine and absorption ... -
Formation Damage Issues Impacting the Productivity of Low Permeability, Low Initial Water Saturation Gas Producing Formations
(The American Society of Mechanical Engineers (ASME), 2005)Very low in situ permeability gas reservoirs (Kgas<0.1mD) are very common and represent a major portion of the current exploitation market for unconventional gas production. Many of these ... -
Evaluation of Horizontal Well Performance After Drilling-Induced Formation Damage
(The American Society of Mechanical Engineers (ASME), 2005)It is well recognized that near-wellbore formation damage can dramatically reduce well productivities, especially for open hole completed horizontal wells. The economic impact of poor productivity ... -
Nonisothermal Compressor Station Optimization
(The American Society of Mechanical Engineers (ASME), 2005)A detailed mathematical model of compressor stations and pipes is essential for optimizing the performance of the gas pipeline system. Most of the available literature on compressor station ... -
Asphaltene Near-well-bore Formation Damage Modeling
(The American Society of Mechanical Engineers (ASME), 2005)When during oil production the thermodynamic conditions within the near-well-bore formation lie inside the asphaltene deposition envelope of the reservoir fluid, the flocculated asphaltenes cause ... -
Impact of Brine Flow and Mixing in the Reservoir on Scale Control Risk Assessment and Subsurface Treatment Options: Case Histories
(The American Society of Mechanical Engineers (ASME), 2005)As offshore production environments become ever more complex, particularly in deepwater regions, the risks associated with formation damage due to precipitation of inorganic scales may increase ... -
Formation Sand Liquefaction: A Mechanism for Explaining Fines Migration and Well Sanding
(The American Society of Mechanical Engineers (ASME), 2005)To understand the basic relationship between the rising water-cut, well sanding, and migration of fines, the author’s work led him to examine the mechanism of well sanding due to sand liquefaction ... -
Formation Damage Induced by Chemical Treatments: Case Histories
(The American Society of Mechanical Engineers (ASME), 2005)This study discusses formation damage mechanisms that were caused by commonly used chemical treatments. The chemicals used in these treatments included a scale inhibitor, a biocide-corrosion ...