Journal of Energy Resources Technology: Recent submissions
Now showing items 2001-2020 of 3450
-
The LETHE™ Gas Turbine Hybrid Prototype Vehicle of the University of Roma 1: Drive Cycle Analysis of Model Vehicle Management Unit
(The American Society of Mechanical Engineers (ASME), 2007)The paper describes the logic of the vehicle’s power management unit (VMU) for the prototype configuration of the LETHE™ (low emissions turbo hybrid electric) vehicle designed by the University ... -
Evaluation of Electricity Generation From Underground Coal Fires and Waste Banks
(The American Society of Mechanical Engineers (ASME), 2007)A temperature response factors model of vertical thermal energy extraction boreholes is presented to evaluate electricity generation from underground coal fires and waste banks. Sensitivity and ... -
Thermal System Interactions in Optimizing Advanced Thermoelectric Energy Recovery Systems
(The American Society of Mechanical Engineers (ASME), 2007)Energy recovery is gaining importance in various transportation and industrial process applications because of rising energy costs and geopolitical uncertainties impacting basic energy supplies. ... -
New API RP2A Tubular Joint Strength Design Provisions
(The American Society of Mechanical Engineers (ASME), 2007)The development of the new API RP2A (22nd edition) parametric static strength prediction equations for planar circular hollow section tubular joints is described. Prediction equations are presented ... -
Modeling of Chemical Processes in a Diesel Engine With Alcohol Fuels
(The American Society of Mechanical Engineers (ASME), 2007)Methanol utilization in a compression ignition engine has held tentative promise for a number of years, and, in fact, the concept has seen large scale field trials intended to demonstrate this ... -
Improvement of Power Generation Efficiency of an Independent Microgrid Composed of Distributed Engine Generators
(The American Society of Mechanical Engineers (ASME), 2007)The power generation efficiency and power cost of an independent microgrid that distributes the power from a small diesel engine power generator was investigated using numerical analysis. The ... -
Investigation of Different Methods to Control a Small Variable-Speed Wind Turbine With PMSM Drives
(The American Society of Mechanical Engineers (ASME), 2007)In this paper, a different control strategy of a small wind generator, including a permanent magnet synchronous machine (PMSM), has been studied. The objective is to analyze the produced power ... -
Analysis of Energy Harvesting Positive Displacement Motor
(The American Society of Mechanical Engineers (ASME), 2007)Drilling operations in deep and ultradeep water are increasing around the world. The development of these substantial prospects provides many challenges and requires the integration of knowledge ... -
Discussion: “Design Improvements to a Biomass Stirling Engine Using Mathematical Analysis and 3D CFD Modeling” [Mahkamov, K., 2006, ASME J. Energy Resour. Technol., 128, pp 203–215]
(The American Society of Mechanical Engineers (ASME), 2007)I was interested in the above paper since the engine involved incorporates the same spherical rocker arm seals as were used on the valve mechanism of a solar thermal water pump which I built ... -
On Simplified Models for the Rate- and Time-Dependent Performance of Stratified Thermal Storage
(The American Society of Mechanical Engineers (ASME), 2007)In direct sensible thermal storage systems, both the energy discharging and charging processes are inherently time-dependent as well as rate-dependent. Simplified models which depict the characteristics ... -
Effects of Splitter Blades on Deep Well Pump Performance
(The American Society of Mechanical Engineers (ASME), 2007)Impellers with splitter blades have been used in turbomachinery design for both pumps and compressors. Increasing the number of blades increases the head of the pump, however, it causes a ... -
Combustion Characteristics of Compression Engine Driven by Emulsified Fuel Under Various Fuel Injection Angles
(The American Society of Mechanical Engineers (ASME), 2007)In this present work, the various emulsified fuel ratios of 50D:50E (50% Diesel No. 2: 50% ethanol 100% proof), 60D:40E, and 70D:30E have been prepared. Performance and emission tests are ... -
Charcoal-Adsorption, Water-Washing, and Air-Dilution Systems to Reduce Diesel Emissions With Special Emphasis on Odor Reduction
(The American Society of Mechanical Engineers (ASME), 2007)Direct injection (DI) diesel engines emit a far more disagreeable exhaust odor than gasoline engines, especially at low temperatures and at idling. There is no proper system of odor reduction ... -
Improving Ethanol Life Cycle Energy Efficiency by Direct Utilization of Wet Ethanol in HCCI Engines
(The American Society of Mechanical Engineers (ASME), 2007)Homogeneous charge compression ignition (HCCI) is a new engine technology with fundamental differences over conventional engines. HCCI engines are intrinsically fuel flexible and can run on low-grade ... -
Optimum Criteria on the Important Parameters of an Irreversible Otto Heat Engine With the Temperature-Dependent Heat Capacities of the Working Fluid
(The American Society of Mechanical Engineers (ASME), 2007)An irreversible cycle model of the Otto heat engine is established, in which the temperature-dependent heat capacities of the working fluid, the irreversibilities resulting from the nonisentropic ... -
Planning 3D Well Trajectories Using Spline-in-Tension Functions
(The American Society of Mechanical Engineers (ASME), 2007)This work presents the mathematical method to design complex trajectories for three-dimensional (3D) wells using spline in tension as coordinate functions. 3D spline-in-tension trajectories are ... -
A Computational Method for Planar Kinematic Analysis of Beam Pumping Units
(The American Society of Mechanical Engineers (ASME), 2007)A generalized computational method for planar kinematic analysis of pumping units is presented in this study. In this method, a local coordinate system is assigned to each body with respect ... -
Experimental Study of Composting Oil Wet Drill Cuttings as a Drilling Waste Disposal Option
(The American Society of Mechanical Engineers (ASME), 2007)This paper presents the potential of composting oil wet drill cuttings as a drilling waste disposal option. The potential is substantiated by results from several laboratory and field experiments. ... -
Transient Optimization in Natural Gas Compressor Stations for Linepack Operation
(The American Society of Mechanical Engineers (ASME), 2007)One of the key factors in the operation of a natural gas pipeline network is the linepack in the network. The desired operation of the network as derived from estimated receipts and deliveries ... -
Closure to “Discussion: ‘Design Improvements to a Biomass Stirling Engine Using Mathematical Analysis and 3D CFD Modeling’ ” (2007, ASME J. Energy Resour. Technol., 129, pp. 278, 279, 280)
(The American Society of Mechanical Engineers (ASME), 2007)First, the current author would like to thank everyone who provided comments in Refs. 1-3 regarding the results published in Ref. 4. The aim of the paper was to demonstrate capabilities of ...