Journal of Energy Resources Technology: Recent submissions
Now showing items 1901-1920 of 3450
-
Diesel Engine Optimization for Electric Hybrid Vehicles
(The American Society of Mechanical Engineers (ASME), 2009)Performance and emission testing for a single cylinder four-stroke diesel engine have been experimentally performed to determine the optimum operation conditions for this engine when it is used ... -
Solar Hydrogen Production Integrating Low-Grade Solar Thermal Energy and Methanol Steam Reforming
(The American Society of Mechanical Engineers (ASME), 2009)In this paper, a novel approach of middle-temperature solar hydrogen production using methanol steam reforming is proposed. It can be carried out at around 200–300°C, much lower than the ... -
Discussion: “Design Improvements to a Biomass Stirling Engine Using Mathematical Analysis and 3D CFD Modeling” (Mahkamov, K., 2006, ASME J. Energy Resour. Technol., 128, pp. 203–215)
(The American Society of Mechanical Engineers (ASME), 2009)For readers wanting to know how computational fluid dynamics (CFD) modeling might help the Stirling engine realize its full potential as a source of sustainable energy, the “closure” from ... -
Rapid Characterization of Radiation and Pollutant Emissions of Biodiesel and Hydrocarbon Liquid Fuels
(The American Society of Mechanical Engineers (ASME), 2009)As a result of decreasing petroleum supplies, new fuel sources, such as transesterified biofeedstock based oils and their blends with petroleum diesel fuels, have emerged with potential to ... -
Experimental Testing of Gerotor and Scroll Expanders Used in, and Energetic and Exergetic Modeling of, an Organic Rankine Cycle
(The American Society of Mechanical Engineers (ASME), 2009)This paper presents the experimental testing of relatively cost-effective expanders in an organic Rankine cycle (ORC) to produce power from low-grade energy. Gerotor and scroll expanders were the ... -
Experimental Study of DRA for Vertical Two-Phase Annular Flow
(The American Society of Mechanical Engineers (ASME), 2009)Experimental investigation of drag reduction in vertical two-phase annular flow is presented. The work is a feasibility test for applying drag reducing additives (DRAs) in high production-rate ... -
Feasibility Investigation and Modeling Analysis of CO2 Sequestration in Arbuckle Formation Utilizing Salt Water Disposal Wells
(The American Society of Mechanical Engineers (ASME), 2009)The rate of CO2 production in many states, primarily from coal-fired power plants, is such that it only takes a few years to fill up any depleted oil and gas reservoirs. In order to reduce ... -
Exergy Analysis of an Industrial Waste Heat Recovery Based Cogeneration Cycle for Combined Production of Power and Refrigeration
(The American Society of Mechanical Engineers (ASME), 2009)In this paper, a novel industrial waste heat recovery based cogeneration is proposed for the combined production of power and refrigeration. The system is an integration of Rankine power cycle ... -
Utilization of Heat, Power, and Recovered Waste Heat for Industrial Processes in the U.S. Chemical Industry
(The American Society of Mechanical Engineers (ASME), 2009)This paper presents energy end-use model of the U.S. Chemical Industry. The model allocates combustible fuel and renewable energy inputs among generic end-uses including intermediate conversions ... -
Energy Process-Step Model of Hydrogen Production in the U.S. Chemical Industry
(The American Society of Mechanical Engineers (ASME), 2009)This paper gives a representative energy process-step model of hydrogen production in the U.S. Chemical Industry based on federal data. There have been prior efforts to create energy process-step ... -
Prediction of Slug Liquid Holdup in Horizontal Pipes
(The American Society of Mechanical Engineers (ASME), 2009)Slug liquid holdup is a critical parameter of slug flow, which influences the average liquid holdup and pressure drop along pipelines. The objective of this study is to develop a new correlation ... -
Cement Seal Failure at Casing Shoe in Shallow Marine Sediments
(The American Society of Mechanical Engineers (ASME), 2009)This paper describes the hypothetical mechanisms of cement seal failure during casing shoe leak-off testing (LOT) of surface holes in the shallow-marine sediments (SMSs)—parting of cement sheath ... -
On the Teaching of Performance Evaluation and Assessment of a Combined Cycle Cogeneration System
(The American Society of Mechanical Engineers (ASME), 2009)Performance evaluation and assessment of combined cycle cogeneration systems are not taught well in academia. One reason is these parameters are scattered in the literature with each publication ... -
Vertical Interference Test in Wells With Downhole Water Sink Completions
(The American Society of Mechanical Engineers (ASME), 2009)Downhole water sink (DWS) well completions segregate production in the wellbore by producing water from the underlying aquifer and oil—from the oil zone of the reservoir. A pump drains water ... -
Energy Conservation Opportunity in Boiler Systems
(The American Society of Mechanical Engineers (ASME), 2009)In this study, “energy efficiency” study has been performed for a natural gas fuelled boiler, operating at 42,000 kPa pressure and 713.15 K temperature, with a nominal capacity of 33.33 kg/s ... -
Inflow Performance Relationships Under Gravity Segregation for Solution Gas-Drive Reservoirs
(The American Society of Mechanical Engineers (ASME), 2009)This paper analyzes the influence of gravity segregation effects on inflow performance relationship (IPR) curves, with both totally and partially penetrated vertical wells. Using synthetic responses ... -
Optimization of Gas Injection Allocation in a Dual Gas Lift Well System
(The American Society of Mechanical Engineers (ASME), 2009)Gas lift is one of the most frequently used artificial lift methods in petroleum industries. The principle of this method is to maintain low well bottomhole pressure by injecting high pressure ... -
Determination of Composition of Cellulose and Lignin Mixtures Using Thermogravimetric Analysis
(The American Society of Mechanical Engineers (ASME), 2009)The proportional composition of cellulose, hemicellulose, lignin, and minerals in a biomass plays a significant role in the proportion of pyrolysis products (bio-oil, char, and gases). Traditionally, ... -
The Quest for More Efficient Industrial Engines: A Review of Current Industrial Engine Development and Applications
(The American Society of Mechanical Engineers (ASME), 2009)This paper addresses the need for efficiency gains in the modern industrial engine as utilized in combined heat and power (CHP) generation and other distributed generation situations. Power ... -
Investigating the Use of Methane as Diesel Fuel in Off-Road Haul Road Truck Operations
(The American Society of Mechanical Engineers (ASME), 2009)A scope study is conducted to investigate the technical and commercial feasibility of converting existing mine haul truck engines to a fuel regime of methane and diesel. A dual fuel engine ...