Journal of Energy Resources Technology: Recent submissions
Now showing items 1881-1900 of 3450
-
A Method for Reduction in the Start-Up Time of a Bubbling Bed Boiler Combustor
(The American Society of Mechanical Engineers (ASME), 2010)A study on the heating of inert bed solids in a bubbling fluidized bed by means of an over-bed start-up oil burner is presented in this paper. Experiments carried out in a 160 mm diameter ... -
CFD Based Ash Deposition Prediction in a BFBC Firing Mixtures of Peat and Forest Residue
(The American Society of Mechanical Engineers (ASME), 2010)Combustion of biofuel mixtures for heat and power production is often combined with ash related operational problems. Their reliable prediction is therefore essential in order to improve boiler ... -
Modeling and Experimental Study of Newtonian Fluid Flow in Annulus
(The American Society of Mechanical Engineers (ASME), 2010)A major concern in drilling operations is the proper determination of frictional pressure loss in order to select a mud pump and avoid any serious problems. In this study, a mechanistic model ... -
Theoretical Analysis and Experimental Study of Dynamic Hydrocyclones
(The American Society of Mechanical Engineers (ASME), 2010)Characteristics of dynamic hydrocyclones are introduced. The advantages of dynamic hydrocyclones, such as wider applicable flowrate range, smaller cut size, etc., are analyzed compared with normally ... -
Production of Biodiesel From Used Mustard Oil and Its Performance Analysis in Internal Combustion Engine
(The American Society of Mechanical Engineers (ASME), 2010)Decline in fossil fuel resources along with high crude oil prices generated attention toward the development of fuel from alternate sources. Such fuel should be economically attractive and ... -
Hydrogen Use in an Urban District: Energy and Environmental Comparisons
(The American Society of Mechanical Engineers (ASME), 2010)Hydrogen technology is becoming ever more relevant because hydrogen use can help in containing greenhouse gas emission if CO2 capture and storage technologies are implemented in the hydrogen ... -
Effect of Biodiesel-Ethanol Blended Fuel Spray Characteristics on the Reduction of Exhaust Emissions in a Common-Rail Diesel Engine
(The American Society of Mechanical Engineers (ASME), 2010)An experimental investigation was performed to analyze the effects of biodiesel-ethanol blended fuel spray on the combustion, and exhaust emission characteristics in a single cylinder common-rail ... -
Life Cycle Cost Analysis of a Novel Cooling and Power Gas Turbine Engine
(The American Society of Mechanical Engineers (ASME), 2010)A life cycle cost analysis was performed to compare life cycle costs of a novel gas turbine engine to those of a conventional microturbine with similar power capacity. This engine, called the ... -
Laminar Flame Velocity of Syngas Fuels
(The American Society of Mechanical Engineers (ASME), 2010)In this present study, burning velocities of H2–CO mixtures (primary constituents of syngas fuels) are measured. Impact of different burner systems, H2 concentration, and different measurement ... -
Exhaust Emissions and Electric Energy Generation in a Stationary Engine Using Blends of Diesel and a Fuel Obtained Through the Low Temperature Conversion Process Applied to Petrochemical Residue
(The American Society of Mechanical Engineers (ASME), 2010)The present work describes an experimental investigation concerning the exhaust emissions and the electric energy generation using blends of diesel and an alternative fuel obtained through the ... -
Drilling Action of Roller-Cone Bits: Modeling and Experimental Validation
(The American Society of Mechanical Engineers (ASME), 2010)This paper presents a new model of the drilling response of roller-cone bits. First, a set of relations between the weight-on-bit W, the torque-on-bit T, the rate of penetration V, and the ... -
Ventilation of Compost Heating System by Permanent Magnets
(The American Society of Mechanical Engineers (ASME), 2010)The effect of a permanent magnet on ventilation of an air duct through compost has been investigated numerically. Some composts yield heat over 60°C in the fermentation process. This ... -
Combustion of Apple Juice Wastes in a Cyclone Combustor for Thermal Energy Generation (ES2009-90152)
(The American Society of Mechanical Engineers (ASME), 2010)The solid waste generated from the apple juice industry (apple bagasse (AB)) was characterized as a fuel, and the potential for its utilization as an alternative energy source was assessed ... -
Residence Time Influence on the Fast Pyrolysis of Loblolly Pine Biomass
(The American Society of Mechanical Engineers (ASME), 2010)Bio-oils were produced within a fast pyrolysis microreactor at 400°C from Pinus taeda (Loblolly pine) with varying residence times. This study has considered six residence times, evaluating ... -
Microhole Coiled Tubing Drilling: A Low Cost Reservoir Access Technology
(The American Society of Mechanical Engineers (ASME), 2009)Although the microhole coiled tubing drilling rigs have been used extensively in Canada, their application in the U.S. has been very limited. In an effort to introduce this technology to the ... -
Design to Maximize Performance of a Thermoelectric Power Generator With a Dynamic Thermal Power Source
(The American Society of Mechanical Engineers (ASME), 2009)It is a difficult technical challenge to design thermoelectric power generation systems that work optimally over a broad dynamic range of thermal input power. Conventional systems are designed ... -
Factors Affecting Sulfur Reactions in High Sulfur Oil Shale Pyrolysis
(The American Society of Mechanical Engineers (ASME), 2009)Oil shale samples from the Ellajjun area south of Jordan were pyrolyzed in different conditions and environments. Sulfur of shale oil was determined using x-ray fluorescence (XRF). Generated ... -
Steady State Productivity Equations for a Vertical Well in Anisotropic Sector Fault, Channel, and Rectangular Reservoirs
(The American Society of Mechanical Engineers (ASME), 2009)This paper presents steady state productivity equations for a fully penetrating vertical well in the following three anisotropic systems: (a) sector fault, (b) channel, and (c) rectangular reservoir ... -
Synthesis of a Novel Ester-Based Drilling Fluid Applicable to High Temperature Conditions
(The American Society of Mechanical Engineers (ASME), 2009)Ester-based drilling fluids based on aliphatic esters were introduced in 1990. Esters can be synthesized from fatty acids and alcohols. Previous studies indicated that ester hydrolysis in drilling ... -
Dynamic Effects of Mandrel/Tubular Interaction on Downhole Solid Tubular Expansion in Well Engineering
(The American Society of Mechanical Engineers (ASME), 2009)The expansion process subjects a solid tubular to large plastic deformations leading to variations in tubular thickness and length, which may result in premature and unexpected failures. It was ...