Journal of Energy Resources Technology: Recent submissions
Now showing items 1841-1860 of 3450
-
Mechanism and Kinetics of Pyrolysis of Coal With High Ash and Low Fixed Carbon Contents
(The American Society of Mechanical Engineers (ASME), 2011)There are much coal with low content of volatile matter (Vad < 20%), high content of ash (Aad > 50%), low heating caloric (∼10,000 kJ/kg) in China. It is very important to study ... -
Aerodynamic Measurements on a Vertical Axis Wind Turbine in a Large Scale Wind Tunnel
(The American Society of Mechanical Engineers (ASME), 2011)This paper presents the first results of a wide experimental investigation on the aerodynamics of a vertical axis wind turbine. Vertical axis wind turbines have recently received particular ... -
Leveling Intermittent Renewable Energy Production Through Biomass Gasification-Based Hybrid Systems
(The American Society of Mechanical Engineers (ASME), 2011)The increased use of intermittent renewable power in the United States is forcing utilities to manage increasingly complex supply and demand interactions. This paper evaluates biomass pathways ... -
Modeling Productivity Index for Long Horizontal Well
(The American Society of Mechanical Engineers (ASME), 2011)Horizontal wells have become a popular alternative for the development of hydrocarbon fields around the world because of their high flow efficiency caused by a larger contact area made with ... -
Sensitivity of Slug Flow Mechanistic Models on Slug Length
(The American Society of Mechanical Engineers (ASME), 2011)Slug flow is one of the common flow patterns in gas and oil production and transportation. One of the closure relationships required by the multiphase flow mechanistic models is slug length ... -
A Modular Differential Dielectric Sensor for Use in Multiphase Separation, Process Measurement, and Control—Part II: Experimental Investigation
(The American Society of Mechanical Engineers (ASME), 2011)Accurate and continuous measurement of the percent water in crude oil production streams (watercut) over 0 to 100% range is critical for petroleum industry. High accuracy and stability are also ... -
Analysis of Postbuckling Drillstring Vibrations in Rotary Drilling of Extended-Reach Wells
(The American Society of Mechanical Engineers (ASME), 2011)One of the most serious concerns of extended-reach drilling is the dynamic behavior of the drillstring and the cleaning of well. Good cleaning requires an increased angular velocity. This paper ... -
Potential Benefits of Plug-In Hybrid Electric Vehicles for Consumers and Electric Power Utilities
(The American Society of Mechanical Engineers (ASME), 2011)Plug-in hybrid electric vehicles (PHEVs) have the potential of substantially reducing petroleum consumption and vehicular CO2 emissions relative to conventional vehicles. The analysis presented in ... -
A Modular Differential Dielectric Sensor for Use in Multiphase Separation, Process Measurement, and Control—Part I: Analytical Modeling
(The American Society of Mechanical Engineers (ASME), 2011)Oil industry increasingly demands accurate and stable continuous measurement of the percent water in crude oil production streams (watercut) over the entire 0 to 100% range. High accuracy and ... -
Non-Darcy Binomial Deliverability Equations for Partially Penetrating Vertical Gas Wells and Horizontal Gas Wells
(The American Society of Mechanical Engineers (ASME), 2011)Many gas reservoirs are with bottom water drive. In order to prevent or delay unwanted water into the wellbore, the producing wells are often completed as partially penetrating vertical wells, ... -
Measurements of the Laminar Burning Velocities for Typical Syngas–Air Mixtures at Elevated Pressures
(The American Society of Mechanical Engineers (ASME), 2011)In the currently reported work, three typical mixtures of H2 , CO, CH4 , CO2 , and N2 have been considered as representative of the producer gas (syngas) coming from biomass gasification. ... -
Annular Pressure Reduction During Primary Cementing
(The American Society of Mechanical Engineers (ASME), 2011)Annular pressure reduction during cementing is a major factor causing annular gas flow. It has been widely accepted and proven experimentally that the pressure reduction phenomenon results from ... -
Publisher’s Note: “Experimental Evaluation of Separation Methods for a Riser Dilution Approach to Dual Density Drilling” [Journal Energy Resources Technology, 2011, 133, 031501]
(The American Society of Mechanical Engineers (ASME), 2011)This article was erroneously published in the September issue. It should have been published in the December special issue on R&D in Offshore Petroleum Technology [1]. -
Experimental Visualization of Two-Phase Flow Inside an Electrical Submersible Pump Stage
(The American Society of Mechanical Engineers (ASME), 2011)Dynamic multiphase flow behavior inside a mixed flow electrical submersible pump (ESP) has been studied experimentally and theoretically for the first time. The overall objectives of this study ... -
From the Editor of Special Issue
(The American Society of Mechanical Engineers (ASME), 2011)This special edition of the Journal of Energy Resources Technology is to highlight nine papers that were presented in Honolulu, Hawaii at the 28th International Conference on Ocean, Offshore, ... -
Modeling Two-Phase Flow Inside an Electrical Submersible Pump Stage
(The American Society of Mechanical Engineers (ASME), 2011)Dynamic multiphase flow behavior inside a mixed flow electrical submersible pump (ESP) has been studied experimentally and theoretically for the first time. The overall objectives of this study ... -
Publisher’s Note: “Transient Wax Gel Formation Model for Shut-In Subsea Pipelines” [Journal Energy Resources Technology, 2011, 133, 033001]
(The American Society of Mechanical Engineers (ASME), 2011)This article was erroneously published in the September issue. It should have been published in the December special issue on R&D in Offshore Petroleum Technology [1]. -
Evaluation of Fracture Asymmetry of Finite-Conductivity Fractured Wells
(The American Society of Mechanical Engineers (ASME), 2010)Nearly all commercial hydraulic fracture design models are based on the assumption that a single fracture is initiated and propagated identically and symmetrically about the wellbore, i.e., the ... -
Supervisory Feed-Forward Control for Real-Time Topping Cycle CHP Operation
(The American Society of Mechanical Engineers (ASME), 2010)This paper presents an energy dispatch algorithm for real-time topping cycle cooling, heating, and power (CHP) operation for buildings with the objective of minimizing the operational cost, primary ... -
Entropy Generation Minimization in a Tubular Solid Oxide Fuel Cell
(The American Society of Mechanical Engineers (ASME), 2010)The aim of the paper is to investigate possible design modifications in tubular solid oxide fuel cell geometry to increase its performance. The analysis of the cell performances is conducted ...