Journal of Energy Resources Technology: Recent submissions
Now showing items 1821-1840 of 3450
-
Physicochemical Properties and Combustion Performance of Gas Oil–Fuel Additives
(The American Society of Mechanical Engineers (ASME), 2012)The current paper reviews the effects of the oxygenated and nitrogenated additives to see the results of the physicochemical efficiency and performance through engine tests work by gas oil ... -
Computational Model of a Hybrid Pressurized Solid Oxide Fuel Cell Generator/Gas Turbine Power Plant
(The American Society of Mechanical Engineers (ASME), 2011)A computational model of a hybrid pressurized solid oxide fuel cell (PSOFC) generator/gas turbine power plant is developed using classical thermodynamic analysis in conjunction with electromechanical, ... -
Performance Analysis of a Novel Compact Flotation Unit
(The American Society of Mechanical Engineers (ASME), 2011)The oil and gas industry produces large quantities of water as a by-product of petroleum production. Discharge specification of produced water requires efficient management and sophisticated ... -
An Advanced Power-Generation System With CO2 Recovery Integrating DME Fueled Chemical-Looping Combustion
(The American Society of Mechanical Engineers (ASME), 2011)Dimethyl ether (DME) is a promising alternative fuel, but direct combustion of DME will result in extra energy penalty for CO2 separation. In this paper, an advanced power-generation system ... -
System Analysis of Thermochemical-Based Biorefineries for Coproduction of Hydrogen and Electricity
(The American Society of Mechanical Engineers (ASME), 2011)Fuels derived from biomass feedstocks are a particularly attractive energy resource pathway given their inherent advantages of energy security via domestic fuel crop production and their renewable ... -
Advanced Deconvolution Technique for Analyzing Multirate Well Test Data
(The American Society of Mechanical Engineers (ASME), 2011)Deconvolution allows the test analyst to estimate the constant-rate transient pressure response of a reservoir-well system, and assists us in system identification and parameter estimation. ... -
Predicting Dynamic Barite Sag in Newtonian-Oil Based Drilling Fluids in Pipe
(The American Society of Mechanical Engineers (ASME), 2011)Barite Sag is the settling of barite particles in the wellbore (or other weighting materials), which results in undesirable fluctuations in drilling fluid density. A variety of major drilling ... -
Experimental Investigation of Boiler Pressure Behavior in Closed-Open-Closed System
(The American Society of Mechanical Engineers (ASME), 2011)A boiler or steam generator is a device used to create steam by applying heat energy to water. Compact boilers are specially designed to generate unlimited amount of steam in short time span ... -
Simultaneous Investigation of Entrained Liquid Fraction, Liquid Film Thickness and Pressure Drop in Vertical Annular Flow
(The American Society of Mechanical Engineers (ASME), 2011)The mechanism of atomization of part of the liquid film to form drops in annular two-phase flow is not entirely understood. It has been observed that drop creation only occurs when there are ... -
Application of Ab Initio Quantum Mechanical Calculations to Investigate Oxidation of C-7 and C-14 Methyl Esters: An Alternative Fuel
(The American Society of Mechanical Engineers (ASME), 2011)Using the GAUSSIAN 03 (, 2004, GAUSSIAN 03 , Revision C.02, Gaussian, Inc., Wallingford, CT) program, the electronic structure of the C-14 and C-7 methyl esters, C14H28O2 (methyl tridecanoate) ... -
Revamping, Energy Efficiency, and Exergy Analysis of an Existing Upstream Gas Treatment Facility
(The American Society of Mechanical Engineers (ASME), 2011)Surface oil and gas treatment facilities in service for decades are likely to be oversized due to the natural depletion of their reservoirs. Despite these plants might have been designed ... -
Technoeconomic Analysis of Microalgae Cofiring Process for Fossil Fuel-Fired Power Plants
(The American Society of Mechanical Engineers (ASME), 2011)The concept of cofiring (algal biomass burned together with coal or natural gas in existing utility power boilers) includes the utilization of CO2 from power plant for algal biomass culture ... -
Thermodynamic Properties of Ionized Gases at High Temperatures
(The American Society of Mechanical Engineers (ASME), 2011)Thermodynamic properties of ionized gases at high temperatures have been calculated by a new model based on local equilibrium conditions. Calculations have been done for nitrogen, oxygen, air, ... -
Flame Hysteresis Effects in Methane Jet Flames in Air-Coflow
(The American Society of Mechanical Engineers (ASME), 2011)Presented are the results of experiments designed to investigate flame lift-off behavior in the hysteresis regime for low Reynolds number turbulent flows. The hysteresis regime refers to the ... -
Performance and Emission Experimental Evaluation and Comparison of a Regenerative Gas Microturbine Using Biodiesel From Various Sources as Fuel
(The American Society of Mechanical Engineers (ASME), 2011)This study aims at carrying out an emission/performance experimental analysis to evaluate and compare the use of pure Biodiesel obtained from different sources: castor, soybean, and palm oil, ... -
Effects of Fuel Injection Timing in the Combustion of Biofuels in a Diesel Engine at Partial Loads
(The American Society of Mechanical Engineers (ASME), 2011)Methyl and ethyl esters of vegetable oils have become an important source of renewable energy with convenient applications in compression-ignition (CI) engines. While the use of biofuels results ... -
Propagation of Regular HCl Acids in Carbonate Rocks: The Impact of an In Situ Gelled Acid Stage
(The American Society of Mechanical Engineers (ASME), 2011)Recent laboratory and field studies indicated that polymer-based in situ gelled acids can cause formation damage. Coreflood experiments using single-stage and multistage acids were conducted at ... -
Distribution of Sand Particles in Horizontal and Vertical Annular Multiphase Flow in Pipes and the Effects on Sand Erosion
(The American Society of Mechanical Engineers (ASME), 2011)Predicting erosion resulting from the impact of solid particles such as sand is a difficult task, since it is dependent on so many factors. The difficulty is compounded if the particles are ... -
Experimental Evaluation of Separation Methods for a Riser Dilution Approach to Dual Density Drilling
(The American Society of Mechanical Engineers (ASME), 2011)A dual gradient, deepwater drilling system based on dilution of riser mud requires economically separating the riser mud into a low density dilution fluid and a higher density drilling fluid. ... -
Transient Wax Gel Formation Model for Shut-In Subsea Pipelines
(The American Society of Mechanical Engineers (ASME), 2011)Physics of wax gel formation during shut-in is analyzed and described over a cross-section of a typical subsea pipeline. Two regions are identified during this process: the liquid and gel ...