Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 781-800 of 5605
-
A Novel Active Rollover Prevention for Ground Vehicles Based on Continuous Roll Motion Detection
(The American Society of Mechanical Engineers (ASME), 2019)To enhance the performance of vehicle rollover detection and prevention, this paper proposes a novel control strategy integrating the mass-center-position (MCP) metric and the active rollover preventer (ARPer) system. The ... -
Reviewer's Recognition
(The American Society of Mechanical Engineers (ASME), 2019) -
Output Feedback Control Surface Positioning With a High-Order Sliding Mode Controller/Estimator: An Experimental Study on a Hydraulic Flight Actuation System
(The American Society of Mechanical Engineers (ASME), 2019)In this paper, an output feedback sliding mode position controller/estimator scheme is proposed to control an single input single output (SISO) system subject to bounded nonlinearities and parametric uncertainties. Various ... -
Impulsive Consensus of Networked Multi-Agent Systems With Distributed Delays in Agent Dynamics and Impulsive Protocols
(The American Society of Mechanical Engineers (ASME), 2019)This paper studies the consensus problem of networked multi-agent systems (NMASs). Distributed delays are considered in the agent dynamics, and we propose a new type of impulsive consensus protocols that also takes into ... -
Hydraulic Modal Analysis in Theory and Practice
(The American Society of Mechanical Engineers (ASME), 2019)Theoretical and experimental modal analyses are treated for hydraulic systems modeled by discrete capacities, inductances, resistances, and fluid lines with dynamic laminar flow. Based on an approximate multi-degrees-of-freedom ... -
Cylinder Specific Pressure Predictions for Advanced Dual Fuel Compression Ignition Engines Utilizing a Two-Stage Functional Data Analysis
(The American Society of Mechanical Engineers (ASME), 2019)In-cylinder pressure is a critical metric that is used to characterize the combustion process of engines. While this variable is measured on many laboratory test beds, in-cylinder pressure transducers are not common on ... -
Direct Adaptive Function Approximation Techniques Based Control of Robot Manipulators
(The American Society of Mechanical Engineers (ASME), 2018)In this paper, a simple model-free controller for electrically driven robot manipulators is presented using function approximation techniques (FAT) such as Legendre polynomials (LP) and Fourier series (FS). According to ... -
Reviewer's Recognition
(The American Society of Mechanical Engineers (ASME), 2018) -
A Control-Oriented Model for Trajectory-Based HCCI Combustion Control
(The American Society of Mechanical Engineers (ASME), 2018)Previously, the authors have proposed the concept of piston trajectory-based homogeneous charge compression ignition (HCCI) combustion control enabled by a free piston engine (FPE) and shown its benefits on both engine ... -
Flight Performance Analysis of Hybrid Airship Considering Added Mass Effects
(The American Society of Mechanical Engineers (ASME), 2018)In this paper, an analysis is applied to a hybrid airship considering the added mass. First, based on the dynamic mesh technology, a computational fluid dynamics (CFD) method is employed to obtain the added mass coefficient ... -
Coupled Dynamic Characteristics of Wind Turbine Gearbox Driven by Ring Gear Considering Gravity
(The American Society of Mechanical Engineers (ASME), 2018)Gravity is usually neglected in the dynamic modeling and analysis of the transmission system, especially in some relatively lightweight equipment. The weight of wind turbine gearbox is up to tens of tons or even hundreds ... -
A Reduced Complexity Model for the Compressor Power of an Automotive Turbocharger
(The American Society of Mechanical Engineers (ASME), 2018)Control-oriented models for automotive turbocharger (TC) compressors typically describe the compressor power assuming an isentropic thermodynamic process with fixed isentropic and mechanical efficiencies for power transmission ... -
Switching Gain-Scheduled Proportional–Integral–Derivative Electronic Throttle Control for Automotive Engines
(The American Society of Mechanical Engineers (ASME), 2018)This paper proposes an application of the switching gain-scheduled (S-GS) proportional–integral–derivative (PID) control technique to the electronic throttle control (ETC) problem in automotive engines. For the S-GS PID ... -
Leader-Following Consensus Control of General Linear Multi-Agent Systems With Diverse Time-Varying Input Delays
(The American Society of Mechanical Engineers (ASME), 2018)This paper addresses the problem of leader-following consensus control of general linear multi-agent systems (MASs) with diverse time-varying input delays under the integral quadratic constraint (IQC) framework. A novel ... -
Calibration and Compensation of Dynamic Abbe Errors of a Coordinate Measuring Machine
(The American Society of Mechanical Engineers (ASME), 2018)Error compensation technology is used for improving accuracy and reducing costs. Dynamic error compensation techniques of coordinate measuring machine (CMM) are still under study; the major problem is a lack of suitable ... -
Analytical and Experimental Study on Passive Stabilization of Thermoacoustic Dynamics in a Rijke Tube
(The American Society of Mechanical Engineers (ASME), 2018)This paper deals with passive stabilization of thermoacoustic dynamics in a Rijke tube using a Helmholtz resonator. Thermoacoustic instabilities result from the dynamic coupling between the heat release and pressure in a ... -
Fast and Precise Glass Handling Using Visual Servo With Unscented Kalman Filter Dual Estimation
(The American Society of Mechanical Engineers (ASME), 2018)In the protective glass manufacturing industry for cell phones, placing glass pieces into the slots of the grinder requires submillimeter accuracy which only can be achieved by human workers, leading to a bottle neck in ... -
First Principle Based Control Oriented Gasoline Engine Model Including Lumped Cylinder Dynamics
(The American Society of Mechanical Engineers (ASME), 2018)A novel first principle based control oriented model of a gasoline engine is proposed which also carries diagnostic capabilities. Unlike existing control oriented models, the formulated model reflects dynamics of the ... -
Hybrid Analog/Digital Control of Bilateral Teleoperation Systems
(The American Society of Mechanical Engineers (ASME), 2018)Hybrid analog/digital control of bilateral teleoperation systems can lead to superior performance (transparency) while maintaining stability compared to pure analog or digital control methods. Such hybrid control is ... -
Probabilistic Data Association-Feedback Particle Filter for Multiple Target Tracking Applications
(The American Society of Mechanical Engineers (ASME), 2018)This paper is concerned with the problem of tracking single or multiple targets with multiple nontarget-specific observations (measurements). For such filtering problems with data association uncertainty, a novel feedback ...