Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 3121-3140 of 5605
-
Experimental Study of the Robust Tracking Control of a Shape Memory Alloy Wire Actuator
(The American Society of Mechanical Engineers (ASME), 2004)This paper presents an experimental study of a tracking control of a shape memory alloy (SMA) wire actuator using a nonlinear robust compensator. The control design uses the sliding-mode approach ... -
Introducing Glory: A Novel Strategy for an Omnidirectional Spherical Rolling Robot
(The American Society of Mechanical Engineers (ASME), 2004)This paper describes a prototype and analytical studies of a spherical rolling robot, a new design of an omnidirectional robot system. The robot can arbitrarily begin to move in any direction ... -
Delay-Independent Observer-Based Control for a Class of Neutral Systems
(The American Society of Mechanical Engineers (ASME), 2004)In this paper, the observer-based control for a class of neutral systems is considered. The analysis is based on the use of Lyapunov functional stability theory. Delay-independent stabilization ... -
LQG Control for Nonstandard Singularly Perturbed Discrete-Time Systems
(The American Society of Mechanical Engineers (ASME), 2004)In this paper we present a control method and a high accuracy solution technique in solving the linear quadratic Gaussian problems for nonstandard singularly perturbed discrete time systems. The ... -
Designing Robust Repetitive Controllers
(The American Society of Mechanical Engineers (ASME), 2004)A method for designing repetitive feedback controllers using nonparametric frequency response plant models is developed. In comparison to the zero-phase-error (ZPE) controller (ASME J. Dyn. Syst. ... -
Robust Performance Limitations and Design of Controlled Delayed Systems
(The American Society of Mechanical Engineers (ASME), 2004)This paper presents performance limitations and a control design methodology for nonminimum phase plants of the pure delay type subject to robustness constraints. Of interest is the design of ... -
Recovery of Signals Distorted by Sensor Nonlinearity
(The American Society of Mechanical Engineers (ASME), 2004)Considered in this paper is a framework for addressing sensor issues that are related to nonlinearity. When a signal is picked up by a nonlinear sensor, it is often the case that the high ... -
String Instabilities in Formation Flight: Limitations Due to Integral Constraints
(The American Society of Mechanical Engineers (ASME), 2004)Flying in formation improves aerodynamic efficiency and, consequently, leads to an energy savings. One strategy for formation control is to follow the preceding vehicle. Many researchers have ... -
Modeling of Complex Manufacturing Processes by Hierarchical Fuzzy Basis Function Networks With Application to Grinding Processes
(The American Society of Mechanical Engineers (ASME), 2004)A framework for modeling complex manufacturing processes using fuzzy neural networks is presented with a novel training algorithm. In this study, a hierarchical structure that consists of fuzzy ... -
Cooperative Control of Vehicle Swarms for Acoustic Target Localization by Energy Flows
(The American Society of Mechanical Engineers (ASME), 2004)A control algorithm has been developed and experimentally validated for guiding swarms of robotic vehicles to acoustic targets. This novel algorithm uses pressure measurements from a set of ... -
Control of Uncertain LTI Systems Based on an Uncertainty and Disturbance Estimator
(The American Society of Mechanical Engineers (ASME), 2004)This paper proposes a robust control strategy for uncertain LTI systems. The strategy is based on an uncertainty and disturbance estimator (UDE). It brings similar performance as the time-delay ... -
Analysis and Model-Based Control of Servomechanisms With Friction
(The American Society of Mechanical Engineers (ASME), 2004)Friction is responsible for several servomechanism limitations, and their elimination is always a challenge for control engineers. In this paper, model-based feedback compensation is studied for ... -
Transient Air/Fuel Ratio Controller Identification Using Repetitive Control
(The American Society of Mechanical Engineers (ASME), 2004)Presented in this paper is a feedforward controller identification process for the transient fueling control of spark ignition (SI) engines. The objective of an SI fueling control system is to ... -
Combined Controller-Observer Design for Uncertain Time Delay Systems With Application to Engine Idle Speed Control
(The American Society of Mechanical Engineers (ASME), 2004)This paper sets forth two approaches for a combined controller-observer design procedure for a class of uncertain time delay systems. The first procedure uses a delay-independent LMI (linear ... -
Estimation, Control and Optimization of Curing in Thick-Sectioned Composite Parts
(The American Society of Mechanical Engineers (ASME), 2004)A nonlinear model-based control method is proposed and validated for controlling, estimating and optimizing the cure in composite parts. During the cure, the exothermic reaction causes temperature ... -
Enhancing Controllability and Observability in Underactuated and Undersensed Systems Through Switching: Application to Vibration Control
(The American Society of Mechanical Engineers (ASME), 2004)Many dynamical systems use transducers that can function both as actuators and sensors. It is possible to continuously switch the functionality of the transducer elements in such systems and ... -
New Adaptive Mode of Operation for MEMS Gyroscopes
(The American Society of Mechanical Engineers (ASME), 2004)This paper presents a new adaptive operation strategy that can identify and, in an adaptive fashion, compensate for most fabrication defects and perturbations affecting the behavior of a MEMS ... -
Blind System Identification of Noncoprime Multichannel Systems and Its Application to Noninvasive Cardiovascular Monitoring
(The American Society of Mechanical Engineers (ASME), 2004)Multichannel blind system identification (MBSI) is a technique for estimating both an unknown input and unknown channel dynamics from outputs measured at different points of the system. MBSI is ... -
On the Origin of Torsional Vibrations in Hot Rolling Mills and a Possible Remedy
(The American Society of Mechanical Engineers (ASME), 2004)Hot rolling mills suffer from severe torsional vibrations in particular working conditions (thin thickness). These vibrations are often explained as the result of an exogenous disturbance amplified ... -
On-Line Adaptation of Grid-Based Look-up Tables Using a Fast Linear Regression Technique
(The American Society of Mechanical Engineers (ASME), 2004)Advanced control systems require accurate process models, while processes are often both nonlinear and time variant. After introducing the identification of nonlinear processes with grid-based ...