Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 2701-2720 of 5605
-
Controller Design Procedure for Two-Mass Systems With Single Flexible Mode
(The American Society of Mechanical Engineers (ASME), 2008)Many manufacturing machines must execute motions as quickly as possible to achieve profitable high-volume production. Most of them exhibit some flexibility, which makes the settling time longer ... -
Nonminimum-Phase Phenomenon of PEM Fuel Cell Membrane Humidifiers
(The American Society of Mechanical Engineers (ASME), 2008)A membrane-based humidifier that uses cooling water of a fuel cell system to humidify the inlet air is modeled and analyzed in this paper. This four-state lumped model is simple and yet ... -
Robust Control of a Parallel- Kinematic Nanopositioner
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents the design, model identification, and control of a parallel-kinematic XYZ nanopositioning stage for general nanomanipulation and nanomanufacturing applications. The stage has a ... -
An Optimal Control Approach to Minimizing Entropy Generation in an Adiabatic Internal Combustion Engine
(The American Society of Mechanical Engineers (ASME), 2008)Entropy generation due to combustion destroys as much as a third of the theoretical maximum work that could have been extracted from the fuel supplied to an engine. Yet, there is no fundamental ... -
Multiharmonic Adaptive Vibration Control of Misaligned Driveline via Active Magnetic Bearings
(The American Society of Mechanical Engineers (ASME), 2008)Active magnetic bearings (AMBs) have been proposed by many researchers and engineers as an alternative to replace traditional contact bearings in rotor and driveshaft systems. Such active, ... -
An Energetic Control Methodology for Exploiting the Passive Dynamics of Pneumatically Actuated Hopping
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents an energetically derived control methodology to specify and regulate the oscillatory motion of a pneumatic hopping robot. An ideal lossless pneumatic actuation system with an ... -
Full Operating Range Robust Hybrid Control of a Coal-Fired Boiler/Turbine Unit
(The American Society of Mechanical Engineers (ASME), 2008)Multi-input-multi-output robust controllers recently designed for the megawatt output/throttle pressure control in a coal-fired power plant boiler/turbine unit have demonstrated performance robustness ... -
H∞ Fuzzy Tracking Control Design for Nonlinear Active Fault Tolerant Control Systems
(The American Society of Mechanical Engineers (ASME), 2008)This paper studies the problem of H∞ fuzzy tracking control design for nonlinear active fault tolerant control systems based on the Takagi and Sugeno fuzzy model. Two random processes with ... -
MIMO Active Vibration Control of Magnetically Suspended Flywheels for Satellite IPAC Service
(The American Society of Mechanical Engineers (ASME), 2008)Theory and simulation results have demonstrated that four, variable speed flywheels could potentially provide the energy storage and attitude control functions of existing batteries and control ... -
Discrete-Time Control of Linear Time-Periodic Systems
(The American Society of Mechanical Engineers (ASME), 2008)A discrete-time control design approach for periodically time-varying systems is introduced. The method employs a period-to-period (point-mapping) formulation of the system’s dynamics and a ... -
Characterization of the Dynamical Response of a Micromachined G-Sensor to Mechanical Shock Loading
(The American Society of Mechanical Engineers (ASME), 2008)Squeeze film damping has a significant effect on the dynamic response of microelectromechanical system (MEMS) devices that employ perforated microstructures with large planar areas and small gap ... -
Command Shaping for Flexible Systems Subject to Constant Acceleration Limits
(The American Society of Mechanical Engineers (ASME), 2008)Input shaping is an effective means of eliminating vibration in many types of flexible systems. This paper discusses how input shaper performance is affected by a fixed acceleration limit. This ... -
Optimizing Learning Convergence Speed and Converged Error for Precision Motion Control
(The American Society of Mechanical Engineers (ASME), 2008)This brief paper considers iterative learning control (ILC) for precision motion control (PMC) applications. This work develops a methodology to design a low pass filter, called the Q-filter, ... -
Variable Structure Decentralized Control and Estimation for Highway Traffic Systems
(The American Society of Mechanical Engineers (ASME), 2008)This work is concerned with the decentralized control of traffic flow in highways using on-ramp metering and variable structure techniques. Both the estimation and the robust control problem are ... -
Rapid Swing-Free Transport of Nonlinear Payloads Using Dynamic Programming
(The American Society of Mechanical Engineers (ASME), 2008)Residual vibration suppression in freely suspended payload transports has been the focus of extensive work in the past. Many methods have been used to address this problem, including both ... -
Fixed Structure Feedforward Controller Design Exploiting Iterative Trials: Application to a Wafer Stage and a Desktop Printer
(The American Society of Mechanical Engineers (ASME), 2008)In this paper, the feedforward controller design problem for high-precision electromechanical servo systems that execute finite time tasks is addressed. The presented procedure combines the selection ... -
Minimax Input Shaper Design Using Linear Programming
(The American Society of Mechanical Engineers (ASME), 2008)The focus of this paper is on the design of robust input shapers where the maximum value of the cost function over the domain of uncertainty is minimized. This nonlinear programming problem ... -
A Robustness Issue of Control Laws Designed by the Input-Shaping Methodology
(The American Society of Mechanical Engineers (ASME), 2008)In this note, a robustness issue of control laws designed by the input-shaping methodology is brought to the fore. A control law designed by this methodology consists of a sequence of step ... -
Servocontrol of the GS16 Turbine Gas Metering Valve by Physics-Based Robust Controller Synthesis
(The American Society of Mechanical Engineers (ASME), 2008)We present a design approach for robust controller synthesis using a μ-synthesis procedure, which returns a controller in an observor/state-feedback form with physically meaningful states. We are ... -
Singularity-Robust Inverse Kinematics Using Lagrange Multiplier for Redundant Manipulators
(The American Society of Mechanical Engineers (ASME), 2008)In this paper, a singularity-robust inverse kinematics is newly suggested by using a Lagrange multiplier for redundant manipulator systems. Two tasks are considered with priority orders under the ...