Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 2681-2700 of 5605
-
Commutational Output Feedback Control for Disk Drive Ramp Loading
(The American Society of Mechanical Engineers (ASME), 2008)The feasibility of a ramp load controller using a conventional disk drive actuator is investigated. The controller eliminates the necessity of increased material requirements common in ramp load ... -
An Analysis Framework for Evaluating Dropout Compensation Strategies in Wireless Servo Systems
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents an approach for analyzing the performance of dropout compensation strategies for linear servo control systems operating over communication channels with losses. A loss of ... -
Spatially Periodic Disturbance Rejection With Spatially Sampled Robust Repetitive Control
(The American Society of Mechanical Engineers (ASME), 2008)Repetitive controllers have been shown to be effective for tracking periodic reference commands or for rejecting periodic disturbances. Typical repetitive controllers are synthesized in temporal ... -
Whirling-Beam Self-Tuning Vibration Absorber
(The American Society of Mechanical Engineers (ASME), 2008)A classic tuned vibration absorber (TVA) is a device that, when attached to a structure, will greatly reduce the motion of the attachment at a specific excitation frequency. When a fixed ... -
Input Shaping Control of Double-Pendulum Bridge Crane Oscillations
(The American Society of Mechanical Engineers (ASME), 2008)Large amplitude oscillation of crane payloads is detrimental to safe and efficient operation. Under certain conditions, the problem is compounded when the payload creates a double-pendulum effect. ... -
On the Practical Stability of Incorporating Integral Compensation Into the Low-and-High Gain Control for a Class of Systems With Norm-Type Input Saturation
(The American Society of Mechanical Engineers (ASME), 2008)This paper studies the practical stability of incorporating integral compensation into the original low-and-high gain feedback law. The motivation for the incorporation is for achieving output ... -
A Polynomial-Based Linear Mapping Strategy for Feedforward Compensation of Hysteresis in Piezoelectric Actuators
(The American Society of Mechanical Engineers (ASME), 2008)A set of memory-based properties is employed in this paper for modeling multiple-path hysteresis response of piezoelectric actuators. These properties, namely, targeting turning points, curve ... -
Model Following Sliding Mode Control Based on Uncertainty and Disturbance Estimator
(The American Society of Mechanical Engineers (ASME), 2008)A new design of sliding mode control based on an uncertainty and disturbance estimator (UDE) is given. The control proposed does not require the knowledge of bounds of uncertainties and ... -
The Application of Command Shaping to the Tracking Problem
(The American Society of Mechanical Engineers (ASME), 2008)This work presents a novel technique for the solution of an optimal input for trajectory tracking. Many researchers have documented the performance advantages of command shaping, which focuses ... -
Transformer Eddy Current Dampers for the Vibration Control
(The American Society of Mechanical Engineers (ASME), 2008)Eddy current dampers are promising for the passive and semiactive vibration control of mechanical structures. Among them, the “motional” types are based on Lorentz forces between a moving conductor ... -
Robust Piecewise-Linear State Observers for Flexible Link Mechanisms
(The American Society of Mechanical Engineers (ASME), 2008)This paper tackles the problem of designing state observers for flexible link mechanisms: An investigation is made on the possibility of employing observers making use of suitable piecewise-linear ... -
Minimum Move-Vibration Control for Flexible Structures
(The American Society of Mechanical Engineers (ASME), 2008)In the rest-to-rest motion of a flexible structure with limited torque or force, it is sometimes important to control the vibrations during the move trajectory as well as at the final time. ... -
Robust Unknown Input Observer for Nonlinear Systems and Its Application to Fault Detection and Isolation
(The American Society of Mechanical Engineers (ASME), 2008)A robust unknown input observer for a nonlinear system whose nonlinear function satisfies the Lipschitz condition is designed based on linear matrix inequality approach. Both noise and uncertainties ... -
Modeling and Control of a Magnetostrictive Tool Servo System
(The American Society of Mechanical Engineers (ASME), 2008)A magnetostrictive actuator offers a long mechanical strain output in a broad bandwidth at a cost of a highly nonlinear magnetic hysteresis. Full utilization of this actuator in precision ... -
Process Feedback Control of the Noncircular Turning Process for Camshaft Machining
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents a frequency domain learning control scheme for a class of nonlinear systems and its application to the process feedback control of the noncircular turning process for camshaft ... -
A Simple Structure for Bilateral Transparent Teleoperation Systems With Time Delay
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents a simple structure design for bilateral teleoperation systems with uncertainties in time delay in communication channel. The goal is to achieve complete transparency and robust ... -
Memoryless Adaptive Controller Design for Uncertain Polynomial Systems With Multiple Time Delays
(The American Society of Mechanical Engineers (ASME), 2008)The stabilization problem is investigated for a class of uncertain systems with multiple time-varying delays. The considered system includes the uncertain nonlinear time delay functions, whose ... -
Modeling and Verification of an Innovative Active Pneumatic Vibration Isolation System
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents a novel concept in active pneumatic vibration isolation. The novelty in the concept is in utilizing an air-spring-orifice-accumulator combination to vary the natural frequency ... -
A Mathematical Model of Driver Steering Control Including Neuromuscular Dynamics
(The American Society of Mechanical Engineers (ASME), 2008)A mathematical driver model is introduced in order to explain the driver steering behavior observed during successive double lane-change maneuvers. The model consists of a linear quadratic regulator ... -
Design, Modeling, and Motion Control of the Noncircular Turning Process for Camshaft Machining
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents the design, modeling, and motion control of the noncircular turning process for camshaft machining. The cam profile tracking performance requirements are first characterized ...