Journal of Structural Engineering: Recent submissions
Now showing items 4281-4300 of 10765
-
Multiple-Tuned Mass Dampers for Multimodal Control of Pedestrian Bridges
(American Society of Civil Engineers, 2012)This paper deals with the allocation and sizing of multiple-tuned mass dampers (MTMDs) in an attempt to retrofit footbridges with multiple critical modes resulting from the excitation of pedestrian traffic. The simple and ... -
Analysis of the Nonlinear Behavior of Timber-Concrete Connections
(American Society of Civil Engineers, 2012)This paper discusses the nonlinear mechanical behavior of timber-concrete structures, mainly when dowel-type fasteners are used in the connections. These nonlinear phenomena result from the nonlinear mechanical behavior ... -
Static Cyclic Response of Partially Grouted Masonry Shear Walls
(American Society of Civil Engineers, 2012)This research investigated the shear behavior of five full-scale partially grouted masonry shear walls (PG-MWs). The walls were built using concrete masonry units, with horizontal reinforcement ratios ranging from 0.085 ... -
Longitudinal Stiffeners in Concrete-Filled Tubes
(American Society of Civil Engineers, 2012)To enhance the strength and constructability of rectangular (or trapezoidal) tubular compression members, reinforced or unreinforced concrete may be filled in the tube. Longitudinal stiffeners are often attached to increase ... -
Uncertainty Analysis of Flexural Overstrength Ratio for RC Columns
(American Society of Civil Engineers, 2012)This paper summarizes the results of a comprehensive statistical study of the flexural overstrength ratio for estimation of the probable flexural strength of ductile RC columns with varying geometries and confinement levels. ... -
Finite-Element Modeling to Calculate the Overall Stiffness of Cracked Reinforced Concrete Beams
(American Society of Civil Engineers, 2012)The macro-finite-element (MFE) modeling proposed in this paper is dedicated to the calculation of the deflection of already cracked reinforced concrete beams under service loading at the stabilized cracking stage. MFEs are ... -
Equilibrium of Pointed, Circular, and Elliptical Masonry Arches Bearing Vertical Walls
(American Society of Civil Engineers, 2012)This paper addresses the long-standing problem of the equilibrium of the circular, pointed, and elliptical arches commonly found in historical masonry buildings and bridges that are subjected to their own weight and the ... -
Elastic Analysis of Beam-Wall Joints Subjected to Out-of-Plane Bending
(American Society of Civil Engineers, 2012)The mechanical performance of reinforced concrete beam-thin-wall joints under out-of-plane bending moments is studied and the analytical solutions in terms of stresses and rotational stiffness of the wall are obtained. For ... -
Seismic Evaluation of Masonry Structures Strengthened with Reinforced Concrete Layers
(American Society of Civil Engineers, 2012)Coating the walls with reinforced concrete layers is a conventional method of strengthening masonry structures in Iran. However, because of the lack of analytical and experimental information about the behavior of strengthened ... -
Direct Strength Design of Cold-Formed C-Sections for Shear and Combined Actions
(American Society of Civil Engineers, 2012)The direct strength method (DSM) recently included in the North American Specification and Australian/New Zealand Standard AS/NZS 4600:2005 gives design rules for compression and bending. No rules are presented in this ... -
Heuristic Approach for Optimum Cost and Layout Design of 3D Reinforced Concrete Frames
(American Society of Civil Engineers, 2012)This paper presents a new methodology for cost optimization of the preliminary layout design of three-dimensional (3D) reinforced concrete (RC) frames. This approach is capable of being easily employed for the optimal ... -
Large Eddy Simulations of Wind-Driven Rain on Tall Building Facades
(American Society of Civil Engineers, 2012)Wind-driven rain (WDR) on building facades may lead to water penetration, cladding damage, structural cracking, etc., which affect the durability of the claddings. This study aims to develop a numerical approach to the ... -
OpenSees-SNOPT Framework for Finite-Element-Based Optimization of Structural and Geotechnical Systems
(American Society of Civil Engineers, 2012)The finite-element (FE) method is widely recognized as a powerful tool in modeling structural and geotechnical systems and simulating their response to static and dynamic loads. In addition, numerical optimization is ... -
Tension Capacity of Staggered Bolted Connections in Cold-Reduced Steel Sheets
(American Society of Civil Engineers, 2012)This paper examines the assumption implicit in Cochrane’s formula that stresses are uniformly distributed across the net section of a staggered bolted connection. The assumption was found to be overoptimistic for connections ... -
Timber Frame Moment Joints with Glued-In Steel Rods. II: Experimental Investigation of Long-Term Performance
(American Society of Civil Engineers, 2012)The pull-out performance of steel rods glued into timber is well-documented, and short-term tests by many researchers have demonstrated reliable strength. The behavior of glued-in steel rods in moment-resisting beam-column ... -
Impact of Residual Stresses and Initial Imperfections on the Seismic Response of Steel Moment Frames
(American Society of Civil Engineers, 2012)The 2010 AISC specification establishes the direct analysis method (DM) as the standard stability analysis and design procedure. Although the DM has important benefits over conventional stability design methods, the interface ... -
Finite-Element Model Updating and Probabilistic Analysis of Timber-Concrete Composite Beams
(American Society of Civil Engineers, 2012)Timber-concrete composite beams are an increasingly common design solution for medium-to-long span floors in new buildings. Thus, there is a significant need for accurate models and analysis tools to predict the response ... -
Performance Control: New Elastic-Plastic Design Procedure for Earthquake Resisting Moment Frames
(American Society of Civil Engineers, 2012)Performance control (PC) is the ability to design a structure in such a way as to expect predetermined modes of response at certain stages of loading, extents of damage, and/or drift ratios. The primary purpose of this ... -
Nonlinear Finite Element Analysis for Cyclic Behavior of Thin-Walled Stiffened Rectangular Steel Columns with In-Filled Concrete
(American Society of Civil Engineers, 2012)The strength, ductility, and energy dissipation capacity of thin-walled, stiffened rectangular concrete-filled steel columns (thin-walled stiffened RCFT columns) subjected to cyclic loads are significantly upgraded by ... -
Section Discretization of Fiber Beam-Column Elements for Cyclic Inelastic Response
(American Society of Civil Engineers, 2012)The paper presents studies of the effect of the number of material integration points at the monitored sections of fiber beam-column elements on the local response of typical structural cross sections under an extensive ...