Journal of Structural Engineering: Recent submissions
Now showing items 4221-4240 of 10765
-
Finite-Element Model Updating for Assessment of Progressive Damage in a 3-Story Infilled RC Frame
(American Society of Civil Engineers, 2013)This paper presents a study on the identification of progressive damage, using an equivalent linear finite-element model updating strategy, in a masonry infilled RC frame that was tested on a shake table. A two-thirds-scale, ... -
Analysis of Thin-Walled Straight Beams with Generally Shaped Closed Sections Using Numerically Determined Sectional Deformation Functions
(American Society of Civil Engineers, 2012)This investigation presents one-dimensional static and eigenvalue analyses of thin-walled straight beams with generally shaped closed single-cell or multicell sections. For accurate beam analysis, sectional warping and ... -
Validation of a Modified Steel Bar Model Incorporating Bond-Slip for Seismic Assessment of Concrete Structures
(American Society of Civil Engineers, 2012)In this paper the implementation and validation of a modified steel bar model including bond-slip of longitudinal bars that was proposed in a companion paper is discussed. The model is developed on the key assumption of ... -
Fatigue Assessment and Service Life Prediction of Existing Steel Bridges by Integrating SHM into a Probabilistic Bilinear S-N Approach
(American Society of Civil Engineers, 2013)Fatigue assessment of several steel bridge details, having equivalent stress range below the constant amplitude fatigue threshold (CAFT), showed that many of these details are free of cracks, although the remaining life ... -
Modified Steel Bar Model Incorporating Bond-Slip for Seismic Assessment of Concrete Structures
(American Society of Civil Engineers, 2012)This paper presents a simplified model for describing the response of a longitudinal bar embedded in concrete, taking into account the bond-slip phenomenon. The model is developed by assuming a linear bond-slip field along ... -
Defect Tolerance for Cast Steel Connections in Braced Frames
(American Society of Civil Engineers, 2012)During the last decade, various steel casting products for steel building structures have been developed, such as connectors between brace members and gusset plates in braced frames. Some casting products are welded to ... -
Out-of-Plane Strength of Confined Masonry Walls
(American Society of Civil Engineers, 2012)This paper presents the results of a study on the out-of-plane behavior of confined masonry walls. Six full-scale walls were tested in a laboratory under incremental uniform pressures. Walls with different aspect ratios, ... -
Seismic Design and Analysis of Steel Plate Shear Walls with Coupling
(American Society of Civil Engineers, 2013)Special steel plate shear walls (SPSWs) are an economical seismic lateral force resisting system used throughout North America and Japan. Architectural constraints often encourage the designer to place a pair of planar ... -
Mechanism of Collapse of Tall Steel Moment-Frame Buildings under Earthquake Excitation
(American Society of Civil Engineers, 2012)The mechanism of collapse of tall steel moment-frame buildings is explored through three-dimensional nonlinear analyses of two 18-story steel moment-frame buildings under earthquake excitation. Both fracture-susceptible ... -
Force- and Displacement-Based Seismic Performance Parameters for Reinforced Masonry Structural Walls with Boundary Elements
(American Society of Civil Engineers, 2012)There is a need to evaluate existing, and introduce new, masonry construction techniques within a performance-based seismic design context to advance their adoption in the next generation of seismic design codes in North ... -
Experimental Study of Cold-Formed Ferritic Stainless Steel Hollow Sections
(American Society of Civil Engineers, 2013)Stainless steel is gaining increasing use in construction because of its durability, favorable mechanical properties, and aesthetic appearance, with the austenitic grades being the most commonly used. Austenitic stainless ... -
Predicting the Usefulness of Monitoring for Identifying the Behavior of Structures
(American Society of Civil Engineers, 2013)Structures can be better understood when measurement data are used to improve the modeling of structural behavior. Our capacity to interpret data depends on aspects such as the choice of model class, model parameters (and ... -
Three-Dimensional Hydromechanical Sectional Analysis of Cracked Nonprismatic Concrete Spillway Piers
(American Society of Civil Engineers, 2012)Several concrete hydraulic structures, such as spillway piers, must be considered three-dimensional (3D) components subjected to 3D loads. A very convenient approach to perform stability analysis of concrete dams is the ... -
Development of a New Composite Slab System Using a Carbon Fiber–Blended Cementitious Adhesive
(American Society of Civil Engineers, 2012)This paper presents an experimental study to develop a new composite slab system consisting of a concrete deck with reinforcing bars, steel plates welded with rib connectors, and a carbon fiber–blended cementitious adhesive. ... -
Design Strength of Locally Buckling Stub-Lipped Channel Columns
(American Society of Civil Engineers, 2012)The compressive strength of cold-formed steel (CFS) lipped channel (LC) members may be governed by yielding, local, distortional, or overall buckling, and any possible interaction among these modes. The direct strength ... -
Benchmark Footbridge for Vibration Serviceability Assessment under the Vertical Component of Pedestrian Load
(American Society of Civil Engineers, 2012)Vibration serviceability criteria are governing the design and determining the cost of modern, slender footbridges. Efficient and reliable evaluation of dynamic performance of these structures usually requires a detailed ... -
In-Plane Elastic Buckling of Shallow Parabolic Arches under an External Load and Temperature Changes
(American Society of Civil Engineers, 2012)This paper studies the in-plane stability of rotationally restrained shallow arches subjected to a vertical uniform load and temperature changes below 100°C. The virtual work principle method was used to establish the ... -
Shear Strength of a Cold-Formed Steel Sheet in Bolted Connections Using Oversized Holes
(American Society of Civil Engineers, 2013)The North American specifications for the design of cold-formed steel (CFS) structural members provides equations for determining the sheet shear strength in bolted connections when standard holes are used. In applications ... -
Bolted Connections in Cold-Formed Steel: Reliability Analysis for Rupture in Net Section
(American Society of Civil Engineers, 2013)This article presents 93 unpublished experimental results for rupture in the net section of bolted connections in cold-formed steel angles and channels. The article includes a study of the strength reduction coefficient ... -
Ambient and Forced Vibration Testing of a Reinforced Concrete Building before and after Its Seismic Retrofitting
(American Society of Civil Engineers, 2013)This paper investigates the effects of seismic retrofitting on the modal characteristics of a 6-story RC building located in Istanbul, Turkey. Ambient vibration surveys were carried out before, during, and after the ...