Show simple item record

dc.contributor.authorY. V. R. K. Prasad
dc.contributor.authorT. Seshacharyulu
dc.contributor.authorVisiting Scientist
dc.contributor.authorW. G. Frazier
dc.contributor.authorSenior Engineer
dc.contributor.authorS. C. Medeiros
dc.contributor.authorResearch Engineer
dc.date.accessioned2017-05-09T00:05:02Z
dc.date.available2017-05-09T00:05:02Z
dc.date.copyrightJuly, 2001
dc.date.issued2001
dc.identifier.issn0094-4289
dc.identifier.otherJEMTA8-27021#355_1.pdf
dc.identifier.urihttp://yetl.yabesh.ir/yetl/handle/yetl/125310
dc.description.abstractDeformation of Ti-6Al-4V alloy in the β phase field is generally considered to be trivial since the material is highly workable at these temperatures and does not normally pose problems during processing. In view of this, studies on the hot deformation behavior of β are scanty compared to those on the α−β deformation. This paper is focussed on understanding the β deformation characteristics in Ti-6Al-4V with a view to examine whether such studies help in optimizing the process design and achieving microstructural control. The emphasis has been on the two industrial grades, viz. commercial purity (CP) versus extra-low interstitial (ELI), and also on the effect of starting microstructure (transformed β versus equiaxed α+β). The stress-strain curves obtained in compression exhibited steady-state behavior at strain rates lower than 1 s−1 and oscillatory/softening behavior at higher strain rates. Kinetic analysis of the flow stress data obtained at different temperatures and strain rates has shown that the stress exponent is about 3.6-3.8 and the apparent activation energy is in the range 150-287 kJ/mole, which is comparable to that of self-diffusion in β phase (150 kJ/mol). Dynamic recrystallization (DRX) of β is identified as the microstructural mechanism in all the cases except in ELI grade with transformed β starting structure. The prior β grain size in the DRX region exhibits a good correlation with the Zener-Hollomon parameter. In case of ELI grade, a mechanism of large grained superplasticity involving sliding of prior colony boundaries has been identified. However, deformation close to the transus in ELI grade causes nucleation of voids which may grow during soaking at the deformation temperature under the influence of tensile residual stress. The results clearly show that a study of β deformation mechanisms holds the key during hot working of Ti-6-4. More importantly, the processing schedule used for CP grade Ti-6-4 should not be used for ELI grade to achieve microstructural control and avoid defects.
dc.publisherThe American Society of Mechanical Engineers (ASME)
dc.titleA Study of Beta Processing of Ti-6Al-4V: Is it Trivial?
dc.typeJournal Paper
dc.journal.volume123
dc.journal.issue3
dc.journal.titleJournal of Engineering Materials and Technology
dc.identifier.doi10.1115/1.1372708
dc.journal.fristpage355
dc.journal.lastpage360
dc.identifier.eissn1528-8889
dc.keywordsFlow (Dynamics)
dc.keywordsDeformation
dc.keywordsTemperature
dc.keywordsDiffusion (Physics)
dc.keywordsSuperplasticity
dc.keywordsStress
dc.keywordsGrain size
dc.keywordsPreforms
dc.keywordsMechanisms
dc.keywordsProduct quality
dc.keywordsOxygen
dc.keywordsNucleation (Physics)
dc.keywordsSteady state
dc.keywordsRecrystallization
dc.keywordsStress-strain curves
dc.keywordsCompression AND Alloys
dc.treeJournal of Engineering Materials and Technology:;2001:;volume( 123 ):;issue: 003
dc.contenttypeFulltext


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record