| dc.contributor.author | T. Iwadate | |
| dc.contributor.author | Y. Tanaka | |
| dc.contributor.author | H. Takemata | |
| dc.date.accessioned | 2017-05-08T23:45:18Z | |
| dc.date.available | 2017-05-08T23:45:18Z | |
| dc.date.copyright | November, 1994 | |
| dc.date.issued | 1994 | |
| dc.identifier.issn | 0094-9930 | |
| dc.identifier.other | JPVTAS-28355#353_1.pdf | |
| dc.identifier.uri | http://yetl.yabesh.ir/yetl/handle/yetl/114217 | |
| dc.description.abstract | A single and generalized prediction method of fracture toughness K IC transition curves of pressure vessel steels has been greatly desired by engineers in the petro-chemical and nuclear power industries, especially from the viewpoint of life extension of reactor pressure vessels. In this paper, the toughness degradation of Cr-Mo steels during long-term service was examined and the two prediction methods of fracture toughness K IC transition curves were studied using the data of 54 heats. 1) The toughness degradation of 2 1/4Cr-1Mo steels levels off within around 50,000 h service. 2) The FATT versus J -factor (=(Si+Mn)(P+Sn)×104 ) and/or X (=(10P+5Sb+4Sn+As)x10−2 ) relationships to estimate the maximum embrittlement of Cr-Mo steels were obtained. 3) A master curve method developed by authors et al.; that is, the method using a KIC /KIC−US versus excess temperature master curve of each material was presented for 2 1/4Cr-1Mo, 1 1/4Cr-1/2Mo, 1Cr and 1/2Mo chemical pressure vessel steels and ASTM A508 C1.1, A508 C1.2, A508 C1.3 and A533 Gr.B C1.1 nuclear pressure vessel steels, where KIC−US is the upper-shelf fracture toughness and excess temperature is test temperature minus FATT. 4) A generalized prediction method to predict the KIC transition curves of any low-alloy steels was developed. This method consists of KIC /KIC−US versus T–T0 master curve and temperature shift ΔT between fracture toughness and CVN impact transition curves versus yield strength relationship, where To is the temperature showing 50 percent KIC−US of the material. 5) The K IC transition curves predicted using both methods showed a good agreement with the lower bound of measured K JC values obtained from J C tests. | |
| dc.publisher | The American Society of Mechanical Engineers (ASME) | |
| dc.title | Prediction of Fracture Toughness KIC Transition Curves of Pressure Vessel Steels From Charpy V-Notch Impact Test Results | |
| dc.type | Journal Paper | |
| dc.journal.volume | 116 | |
| dc.journal.issue | 4 | |
| dc.journal.title | Journal of Pressure Vessel Technology | |
| dc.identifier.doi | 10.1115/1.2929601 | |
| dc.journal.fristpage | 353 | |
| dc.journal.lastpage | 358 | |
| dc.identifier.eissn | 1528-8978 | |
| dc.keywords | Steel | |
| dc.keywords | Pressure vessels | |
| dc.keywords | Fracture toughness | |
| dc.keywords | Impact testing | |
| dc.keywords | Temperature | |
| dc.keywords | Toughness | |
| dc.keywords | Reactor vessels | |
| dc.keywords | Yield strength | |
| dc.keywords | Petrochemicals | |
| dc.keywords | ASTM International | |
| dc.keywords | Alloys | |
| dc.keywords | Engineers | |
| dc.keywords | Nuclear power | |
| dc.keywords | Life extension AND Embrittlement | |
| dc.tree | Journal of Pressure Vessel Technology:;1994:;volume( 116 ):;issue: 004 | |
| dc.contenttype | Fulltext | |