Journal of Electrochemical Energy Conversion and Storage: Recent submissions
Now showing items 181-200 of 486
-
A Fast Screening and Recombinant Method Based on Short-Time Pulse Discharge and Electrochemical Impedance Spectroscopy for Decommissioned Power Batteries
(The American Society of Mechanical Engineers (ASME), 2022)Aiming at the problems of low screening efficiency, high energy consumption and low grouping rate of decommissioned power batteries at this stage, a fast screening and recombinant method based on short-time pulse discharge ... -
Optimization of Cathode Structure for Anode-Supported Planar Solid Oxide Fuel Cell
(The American Society of Mechanical Engineers (ASME), 2022)It is always an important research direction to improve the performance of solid oxide fuel cells (SOFCs) through structural optimization. For anode-supported SOFC, the thin cathode thickness results in an uneven distribution ... -
One-Pot Pyrolysis to Nitrogen-Doped Hierarchically Porous Carbon Nanosheets as Sulfur-Host in Lithium–Sulfur Batteries
(The American Society of Mechanical Engineers (ASME), 2022)Lithium–sulfur battery is a promising energy storage device because of its high theoretical specific energy density, low cost, and environmental friendliness. Here, we prepared nitrogen-doped hierarchically porous carbon ... -
Impedance-Based Performance Analysis of Micropatterned Polymer Electrolyte Membrane Fuel Cells
(The American Society of Mechanical Engineers (ASME), 2022)Micropatterns applied to proton exchange membranes can improve the performance of polymer electrolyte fuel cells -
Lithium-Ion Power Battery Grouping: A Multisource Data Fusion-Based Clustering Approach and Distributed Deployment
(The American Society of Mechanical Engineers (ASME), 2022)Consistence of lithium-ion power battery significantly affects the life and safety of battery modules and packs. To improve the consistence, battery grouping is employed, assembling batteries with similar electrochemical ... -
Graphene Oxide-Induced Carbon Nanoporous Framework Towards Advanced Composite Anode Material for Lithium-Ion Batteries
(The American Society of Mechanical Engineers (ASME), 2021)Porous structures in anode materials are of importance to accommodate volume dilation of active matters. In the present case, a carbon nanoporous framework is hydrothermally synthesized from glucose in the presence of ... -
State of Health Estimation Method for Lithium-Ion Batteries Based on Nonlinear Autoregressive Neural Network Model With Exogenous Input
(The American Society of Mechanical Engineers (ASME), 2021)The working state of lithium-ion batteries must be estimated accurately and efficiently in the battery management system. Building a model is the most prevalent way of predicting the battery's working state. Based on the ... -
Influence of Deep-Discharge Rate on Recycle Process of High Energy Density Traction Batteries
(The American Society of Mechanical Engineers (ASME), 2021)Lithium-ion traction batteries are increasingly used in transportation, such as electric vehicles and buses. To reduce the life cycle cost of traction batteries, material recycling is a technical route that must be considered. ... -
Tuning the Cationic Ratio of Fe1CoxNiyP Integrated on Vertically Aligned Reduced Graphene Oxide Array via Electroless Plating as Efficient Self-Supported Bifunctional Electrocatalyst for Water Splitting
(The American Society of Mechanical Engineers (ASME), 2021)Water splitting is considered as a potential sustainable and green technology for producing mass hydrogen and oxygen. A cost-effective self-supported stable electrocatalyst with excellent electrocatalytic performance in a ... -
Influence of Surface Structure on Performance of Inkjet Printed Cathode Catalyst Layers for Polymer Electrolyte Fuel Cells
(The American Society of Mechanical Engineers (ASME), 2021)The structure of the cathode catalyst layer (CCL) is critically important for improving the performance, durability, and stability of polymer electrolyte fuel cells (PEFCs). In this study, we designed CCLs with a ... -
Special Section on Mass and Charge Transport in Fuel Cells and Metal-Ion Batteries
(The American Society of Mechanical Engineers (ASME), 2021)Given the increasing energy demand and carbon dioxide emission, countries all over the world are vigorously developing sustainable and clean energy. Fuel cells and metal-ion batteries that directly convert chemical energy ... -
Relationship of Chemical Composition and Moisture Sensitivity in LiNixMnyCo1−X−YO2 for Lithium-Ion Batteries
(The American Society of Mechanical Engineers (ASME), 2021)Chemical composition–moisture sensitivity relationship of LiNixMnyCo1−x−yO2 (NMC) cathode materials was investigated by exploring crystal structures, surface properties, and electrochemical performance behaviors of various ... -
Hydrothermally Reduced Graphene Oxide–Coated Carbon Cloth for Flexible Supercapacitors
(The American Society of Mechanical Engineers (ASME), 2021)Hydrothermally synthesized graphene (HRG) was tested for its supercapacitive behavior using nickel (Ni) and hydrothermally treated carbon cloth as current collectors, respectively. Performance evaluation studies were carried ... -
Real-Time State of Charge Estimation of the Extended Kalman Filter and Unscented Kalman Filter Algorithms Under Different Working Conditions
(The American Society of Mechanical Engineers (ASME), 2021)In the battery management system (BMS), the state of charge (SOC) is a very influential factor, which can prevent overcharge and over-discharge of the lithium-ion battery (LIB). This paper proposed a battery modeling and ... -
Experimental Study on Influence of Temperature and C-Rate of Discharge on Performance of In-House-Fabricated 30-Ah Li-Ion Prismatic Cell Made With Lithium Iron Phosphate and MCMB
(The American Society of Mechanical Engineers (ASME), 2021)An experimental study was carried out to quantify the influence of temperature and different C-rate of discharge on in-house fabricated lithium-ion (Li-ion) cell. A 30-Ah Li-ion cell is made of lithium iron phosphate (LFP) ... -
Remaining Useful Life Prediction of Lithium Battery Based on Sequential CNN–LSTM Method
(The American Society of Mechanical Engineers (ASME), 2021)Among various methods for remaining useful life (RUL) prediction of lithium batteries, the data-driven approach shows the most attractive character for non-linear relation learning and accurate prediction. However, the ... -
Creep and Anisotropy of Free-Standing Lithium Metal Foils in an Industrial Dry Room
(The American Society of Mechanical Engineers (ASME), 2021)Commercialization of energy-dense lithium metal batteries relies on stable and uniform plating and stripping on the lithium metal anode. In electrochemical-mechanical modeling of solid-state batteries, there is a lack of ... -
Cycling-Induced Microstructural Changes in Alloy Anodes for Lithium-Ion Batteries
(The American Society of Mechanical Engineers (ASME), 2021)High-capacity electrochemical alloying materials, such as tin and tin-based alloys, present an opportunity for the advancement of lithium-ion batteries. However, the destructive effects of volumetric expansion must be ... -
Robust Passivity-Based Control Scheme for 1.26 KW Proton Exchange Membrane Fuel Cell Under Temperature and Load Variations
(The American Society of Mechanical Engineers (ASME), 2021)The model-based system engineering (MBSE) is based on simplified mathematical models that reflect the dynamic behavior of the systems. These are most of the time nonlinear and need control schemes taking in consideration ... -
Overdischarge Detection and Prevention With Temperature Monitoring of Li-Ion Batteries and Linear Regression-Based Machine Learning
(The American Society of Mechanical Engineers (ASME), 2021)This work focuses on the use of linear regression analysis-based machine learning for the prediction of the end of discharge of a prismatic Li-ion cell. The cell temperature was recorded during the cycling of Li-ion cells ...