YaBeSH Digital Library: Recent submissions
Now showing items 1461-1480 of 316660
-
Synergistic Effects of Different Burner Arrangements on Combustion Characteristics of 100 MW Boiler
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Low nitrogen combustion constitutes a key technology for industrial pollution control and an important direction for clean energy utilization. This article investigates different arrangements of burners, aiming ... -
Performance Optimization and Experimental Investigation of Organic Rankine Cycle System Using Binary Zeotropic Mixtures
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. This study proposes a novel optimization method to enhance the behavior of organic Rankine cycle (ORC) systems through utilizing zeotropic mixtures with temperature glide characteristics. The mixture is created ... -
Data-Driven Monitoring of Offshore Wind Turbine Bearing Temperature Using Adaptive Sparse Attention and Uncertainty Quantification
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. With the rapid development of the offshore wind power industry, ensuring the stability and safety of wind turbines has become increasingly important. As a critical component, the temperature of wind turbine ... -
Thermodynamic Analysis of Microalgae–Plastic Co-Gasification: Impacts on Syngas Composition and Combustion Potential
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. This study addresses the challenge of high ash content in microalgae, which negatively affects gasification efficiency and reactor performance, by blending microalgae with plastic waste. This approach mitigates ... -
Optimization of Biomass Pellet Composition for Enhanced Syngas Quality and Energy Efficiency Using Causal Discovery and Non-Dominated Sorting Genetic Algorithm II
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. The increasing demand for sustainable and renewable energy sources has driven significant interest in biomass as a viable alternative source, which also converts waste into energy. The work has focused on designing ... -
Fuel Injection Strategies for Optimized Combustion and Emissions in a Gasoline Direct Injection Engine
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. With gasoline direct injection, fuel injection parameters should be optimally tuned since they are critical in determining the fuel–air mixing and the charge quality during combustion. Fuel injection timing and ... -
Integrating In-Well Hydrogen Production and CO2 Utilization Through In Situ Combustion Gasification From a Field-Scale System
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. This study investigates numerically the field scale application of in-situ combustion gasification (ISCG) for hydrogen production while simultaneously enhancing oil recovery and CO2 utilization. The numerical ... -
Analytical Forced Imbibition Model Considering Flowrate in Fracture and Oil Droplet Detachment
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. The analysis of forced imbibition efficiency has always been a hotspot in various research domains. The difficulty of forced imbibition lies in the nonlinear imbibition equations coupled with the dynamic flows ... -
Thermal Attenuation Pattern in Long-Distance CO2 Transport Pipeline: Implications for Careful Heat Management
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. The inherent thermal dissipation during long-distance CO2 pipeline transport poses significant challenges to operational safety and efficiency, particularly regarding hydrate formation and pipeline blockages. ... -
Experimental Optimization and Empirical Correlations of CO2 Huff-and-Puff in Tight Sandy Conglomerate Reservoirs
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. The efficient development of tight sandy conglomerate reservoirs remains challenging due to their complex pore structures and ultra-low permeability. This study aims to provide operational guidance for CO2 ... -
A Numerical Method for Predicting Liquid Loading of Condensate Gas Wells
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Condensate gas wells always experience three phases (gas–water–condensate oil) flow in the wellbore; the interaction between each phase is more complicated, which aggravates the liquid loading and causes severe ... -
Nonlinear Coupling of Solid–Liquid Invasion Damage in Tight Sandstone Reservoirs: A Multiscale Characterization and Suppression Modeling Approach
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Formation damage in tight sandstone reservoirs is commonly evaluated by assuming that solid-phase plugging and liquid-phase filtrate invasion act independently and contribute linearly to permeability loss. In ... -
Modeling Transient Behavior of High-Velocity Non-Darcy Flow for a Fractured Vertical Gas Well in a Composite Reservoir
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. High-velocity non-Darcy (HVND) effect has been validated to be an important phenomenon that can influence the transient behavior of gas flow in high-conductivity media. Based on Barree–Conway's equation, an HVND ... -
Effect of Diffuser Inlet Angles on the Power and Torque Coefficients of a Hydrokinetic Turbine
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Ocean current energy is a promising ocean renewable energy source. The Savonius hydrokinetic turbine (HKT) is known for its simplicity and adaptability in low-velocity ocean currents, but its efficiency is generally ... -
A Novel Numerical Pressure Transient Model of the Multifractured Horizontal Well With Nonuniform Gas Production Profile
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Nonuniform gas production profile has been observed due to reservoir heterogeneity, different fracturing scale, and nonuniform distribution of fractures along horizontal wellbore. Different hydraulic fractures ... -
A Hybrid Convolutional Neural Network–Transformer Neural Network Model for Permeability Prediction in Rock Porous Media
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Permeability is a crucial property indicating the fluid transport capability of rock porous media (RPM). This study introduces ConViT, a novel deep learning model that synergistically integrates vision transformer ... -
Exploring Thermal Regulation in Low-Pressure Adsorption Tanks for CO2 Compression Energy Storage
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Compressed CO2 energy storage (CCES) presents a viable alternative to compressed air energy storage (CAES), offering distinct advantages. However, the storage of low-pressure CO2 poses a notable challenge. We ... -
Numerical Simulation Study on Combustion and Emission Characteristics of Cylindrical Porous Media Burners
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Porous media burners offer significant advantages due to their high efficiency and low emissions. Nevertheless, a substantial challenge in the field of porous media burner research pertains to the precise control ... -
Integration of a Rotary Pressure Exchanger in CO2-Based Refrigeration System: Thermodynamic Modeling and Energy–Environmental Benefits
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. This article presents a comprehensive investigation into a sustainable and energy-efficient refrigeration solution for supermarkets operating in warm to hot climates. The study explores the integration of a ... -
A Dynamic Model for Performance and Efficiency of Evaporative Cooling Towers
(The American Society of Mechanical Engineers (ASME), 2026)Abstract. Evaporative cooling towers are critical solutions to engineering design. Due to the complexity of the heat rejection mechanism and the commonality of the evaporative cooling application, there exists a significant ...