Performance Improvement of Piston Engine in Aeronautics by Means of Additive Manufacturing TechnologiesSource: Journal of Aerospace Engineering:;2021:;Volume ( 034 ):;issue: 005::page 04021065-1Author:Guido Saccone
,
Giovanni Andreutti
,
Davide Lucariello
,
Carmine Pirozzi
,
Stefania Franchitti
,
Rosario Borrelli
,
Cinzia Toscano
,
Ciro Pascarella
,
Paolo Caso
,
Fabrizia Caiazzo
DOI: 10.1061/(ASCE)AS.1943-5525.0001305Publisher: ASCE
Abstract: Nowadays, greenhouse gases are a worldwide environmental issue. This is why a significant reduction of pollutant emissions inducing a considerable slowing down of climate change is a matter of primary importance. This topic is dramatically influencing the future of industrial production, and thus, also in the aeronautical field, it is becoming a very important technology driver. Advanced diesel engines are promising solutions to achieve a more fuel-efficient aircraft due to their high efficiency and ability to use widely available and low-cost jet and diesel fuels. In this work, innovative electron beam melting (EBM) additive layer manufacturing (ALM) technologies of titanium alloy were applied to the two-strokes, common rail, GF56 diesel engine, designed and developed by the CMD Company for aeronautic applications. The additive-oriented lattice configuration allowed, through a new design, a substantial saving of weight for the engine, as well as a topological optimization and fabrication of alternative connecting rods of a GF56 engine. After a preliminary investigation of EBM process parameters and mechanical characterization of titanium alloy samples, the obtained engine component prototypes were structurally investigated, topologically optimized, and three-dimensionally (3D) printed. Finally, the overall performance improvement on a typical general aviation (GA) aircraft was estimated by comparing the conventional engine with the optimized GF56 propulsion system.
|
Collections
Show full item record
| contributor author | Guido Saccone | |
| contributor author | Giovanni Andreutti | |
| contributor author | Davide Lucariello | |
| contributor author | Carmine Pirozzi | |
| contributor author | Stefania Franchitti | |
| contributor author | Rosario Borrelli | |
| contributor author | Cinzia Toscano | |
| contributor author | Ciro Pascarella | |
| contributor author | Paolo Caso | |
| contributor author | Fabrizia Caiazzo | |
| date accessioned | 2022-02-01T21:48:15Z | |
| date available | 2022-02-01T21:48:15Z | |
| date issued | 9/1/2021 | |
| identifier other | %28ASCE%29AS.1943-5525.0001305.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl1/handle/yetl/4272060 | |
| description abstract | Nowadays, greenhouse gases are a worldwide environmental issue. This is why a significant reduction of pollutant emissions inducing a considerable slowing down of climate change is a matter of primary importance. This topic is dramatically influencing the future of industrial production, and thus, also in the aeronautical field, it is becoming a very important technology driver. Advanced diesel engines are promising solutions to achieve a more fuel-efficient aircraft due to their high efficiency and ability to use widely available and low-cost jet and diesel fuels. In this work, innovative electron beam melting (EBM) additive layer manufacturing (ALM) technologies of titanium alloy were applied to the two-strokes, common rail, GF56 diesel engine, designed and developed by the CMD Company for aeronautic applications. The additive-oriented lattice configuration allowed, through a new design, a substantial saving of weight for the engine, as well as a topological optimization and fabrication of alternative connecting rods of a GF56 engine. After a preliminary investigation of EBM process parameters and mechanical characterization of titanium alloy samples, the obtained engine component prototypes were structurally investigated, topologically optimized, and three-dimensionally (3D) printed. Finally, the overall performance improvement on a typical general aviation (GA) aircraft was estimated by comparing the conventional engine with the optimized GF56 propulsion system. | |
| publisher | ASCE | |
| title | Performance Improvement of Piston Engine in Aeronautics by Means of Additive Manufacturing Technologies | |
| type | Journal Paper | |
| journal volume | 34 | |
| journal issue | 5 | |
| journal title | Journal of Aerospace Engineering | |
| identifier doi | 10.1061/(ASCE)AS.1943-5525.0001305 | |
| journal fristpage | 04021065-1 | |
| journal lastpage | 04021065-9 | |
| page | 9 | |
| tree | Journal of Aerospace Engineering:;2021:;Volume ( 034 ):;issue: 005 | |
| contenttype | Fulltext |