YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Far Back End of Line Aluminum Stress Reduction Methods for Two-Dimensional/2.5D Fine Pitch Assemblies

    Source: Journal of Electronic Packaging:;2017:;volume( 139 ):;issue: 003::page 31004
    Author:
    Tunga, Krishna
    ,
    Wassick, Thomas
    ,
    Cournoyer, Maryse
    DOI: 10.1115/1.4036368
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: Fine pitch interconnects when used with two-dimensional (2D)/2.5D packaging technology offer enormous potential toward decreasing signal latency and by making it possible to package increased electrical functionality within a given area. However, fine pitch interconnects present their own set of challenges not seen in packages with coarse pitch interconnects. Increased level of stresses within the far back end of line (FBEOL) layers of the chip is the primary concern. Seven different types of 2D and 2.5D test vehicles with fine pitch and coarse pitch interconnects were built and tested for mechanical integrity by subjecting them to accelerated thermal cycling between −55 °C and 125 °C. Finite element based mechanical modeling was done to determine the stress level within the FBEOL layers of these test vehicles. For all the tested assemblies, experimental data and modeling results showed a strong correlation between reduced pitch and increased level of stresses and increased incidence of failures within the FBEOL region. These failures were observed exclusively at the passivation layer and aluminum pad interface. Experimental data in conjunction with mechanical modeling were used to determine a safe level of stress at the aluminum to passivation layer interface. Global and local design changes were explored to determine their effect on the stresses at this interface. Several guidelines have been provided to reduce these stresses for a 2D/2.5D package assembly with fine pitch interconnects. Finally, a reliable low stress configuration, which takes into account all the design changes, has been proposed, which is expected to be robust with very low risk of failure within the FBEOL region.
    • Download: (1.616Mb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Far Back End of Line Aluminum Stress Reduction Methods for Two-Dimensional/2.5D Fine Pitch Assemblies

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/4236865
    Collections
    • Journal of Electronic Packaging

    Show full item record

    contributor authorTunga, Krishna
    contributor authorWassick, Thomas
    contributor authorCournoyer, Maryse
    date accessioned2017-11-25T07:21:04Z
    date available2017-11-25T07:21:04Z
    date copyright2017/14/6
    date issued2017
    identifier issn1043-7398
    identifier otherep_139_03_031004.pdf
    identifier urihttp://138.201.223.254:8080/yetl1/handle/yetl/4236865
    description abstractFine pitch interconnects when used with two-dimensional (2D)/2.5D packaging technology offer enormous potential toward decreasing signal latency and by making it possible to package increased electrical functionality within a given area. However, fine pitch interconnects present their own set of challenges not seen in packages with coarse pitch interconnects. Increased level of stresses within the far back end of line (FBEOL) layers of the chip is the primary concern. Seven different types of 2D and 2.5D test vehicles with fine pitch and coarse pitch interconnects were built and tested for mechanical integrity by subjecting them to accelerated thermal cycling between −55 °C and 125 °C. Finite element based mechanical modeling was done to determine the stress level within the FBEOL layers of these test vehicles. For all the tested assemblies, experimental data and modeling results showed a strong correlation between reduced pitch and increased level of stresses and increased incidence of failures within the FBEOL region. These failures were observed exclusively at the passivation layer and aluminum pad interface. Experimental data in conjunction with mechanical modeling were used to determine a safe level of stress at the aluminum to passivation layer interface. Global and local design changes were explored to determine their effect on the stresses at this interface. Several guidelines have been provided to reduce these stresses for a 2D/2.5D package assembly with fine pitch interconnects. Finally, a reliable low stress configuration, which takes into account all the design changes, has been proposed, which is expected to be robust with very low risk of failure within the FBEOL region.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleFar Back End of Line Aluminum Stress Reduction Methods for Two-Dimensional/2.5D Fine Pitch Assemblies
    typeJournal Paper
    journal volume139
    journal issue3
    journal titleJournal of Electronic Packaging
    identifier doi10.1115/1.4036368
    journal fristpage31004
    journal lastpage031004-8
    treeJournal of Electronic Packaging:;2017:;volume( 139 ):;issue: 003
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian