Journal of Fluids Engineering: Recent submissions
Now showing items 8961-8980 of 9024
-
Two-Phase Flow Through Normal Shock Wave
(The American Society of Mechanical Engineers (ASME), 1975)The steady, one-dimensional flow of compressible gas containing particles through a normal shock wave is investigated. Following the derivation of a set of general equations, two extreme cases ... -
The Paradox of the Vena Contracta
(The American Society of Mechanical Engineers (ASME), 1975)The preponderance of evidence, both theoretical and experimental, appears to show that the vena contracta does not occur at the same location as the minimum pressure point in the Reynolds ... -
A New Algorithm for the Solution of Turbomachinery Flow Problems
(The American Society of Mechanical Engineers (ASME), 1975)A new algorithm, which is a modification of the successive over-relaxation method, has been applied to the inviscid compressible blade-to-blade flow problem. When this procedure was used, an ... -
Some Unresolved Problems in the Fluid Mechanics of Combustion
(The American Society of Mechanical Engineers (ASME), 1975)In spite of the growing shortage of fossil fuels, combustion technology will be required throughout the foreseeable future. This cursory survey of the current state of the art shows that the ... -
Effects of Major Design and Operating Parameters on Achieving Low Emissions From Gas Turbine Combustors
(The American Society of Mechanical Engineers (ASME), 1975)The results of a research program involving the design and performance testing of two low-emission combustors for vehicular gas turbine applications are described. The novel features of the ... -
A Short Diffuser With Low Pressure Loss
(The American Society of Mechanical Engineers (ASME), 1975)A new design concept for gas turbine diffusers is presented and its potential verified by experimental data. The data were obtained from a series of research diffusers, both tubular and annular, ... -
Current and Future Trends and Problems in Combustion: A Summary of the Panel Discussion Session, Fluid Mechanics of Combustion Symposium Fluids Engineering Division Conference, May 1974
(The American Society of Mechanical Engineers (ASME), 1975) -
Numerical Calculations of Turbulent Swirling Flow
(The American Society of Mechanical Engineers (ASME), 1975)A numerical technique is developed for solving axisymmetric, incompressible, turbulent swirling flow problems. The Reynolds stresses are expressed in terms of a scalar turbulent viscosity, μt = ... -
The Influence of Air and Liquid Properties on Airblast Atomization
(The American Society of Mechanical Engineers (ASME), 1975)An experimental study of airblast atomization has been conducted using a specially designed atomizer in which the liquid is first spread into a thin sheet and then exposed on both sides to ... -
Effect of Velocity Slip on the Burning Rate of Fuel Particles
(The American Society of Mechanical Engineers (ASME), 1975)The burning rate of fuel particles often is limited by the rate at which gaseous reactants can diffuse to the particle surface. Under such conditions, the diffusion limitation can be reduced ... -
Discussion: “Analysis of Pressure Wave Reflection in the Male Urethra for the Purpose of Diagnosing Obstructions” (Lai-Fook, S. J., and Gessner, F. B., 1974, ASME J. Fluids Eng., 96, pp. 323–332)
(The American Society of Mechanical Engineers (ASME), 1975) -
Fluid Mechanics of Combustion Symposium Issue
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Turbulent Flow in the Entry Region of a Rough Pipe” (Wang, Jeng-Song, and Tullis, J. P., 1974, ASME J. Fluids Eng., 96, pp. 62–68)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Shock-Excited Pulsation of Large Air Bubbles in Water” (Jensen, F. B., 1974, ASME J. Fluids Eng., 96, pp. 389–393)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “A Contribution to the Numerical Solution of Developing Laminar Flow in the Entrance Region of Concentric Annuli With Rotating Inner Walls” (Coney, J. E. R., and El-Shaarawi, M. A., 1974, ASME J. Fluids Eng., 96, pp. 333–340)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Design and Construction of a Wind Tunnel for Mass Transfer Studies in Incompressible Boundary Layers” (Watts, K. C., Brundrett, E., Nicoll, W. B., and Strong, A. B., 1974, ASME J. Fluids Eng., 96, pp. 311–316)
(The American Society of Mechanical Engineers (ASME), 1975) -
Review—Transition in Nonreversing Oscillating Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1975)Literature on transition in oscillating boundary layers is relatively recent and confusing. The paper first reviews the current thinking on transition in steady boundary layers and on the role ... -
An Optimum Step Design for Centering of Pistons
(The American Society of Mechanical Engineers (ASME), 1975)A stepped lands piston enclosed within a tight circular cylinder of uniform bore and subjected to unequal upstream and down-stream boundary pressures is analysed for the case of incompressible ... -
The Limitations of Solutions of a Third-Order Differential Equation Arising in the Asymptotic Expansions in Radial Jets
(The American Society of Mechanical Engineers (ASME), 1975)It is shown that an equation arising in a study of the asymptotic expansions in radial jets is limited to one meaningful coefficient value. -
Reynolds Stress Tensors in an End-Wall Three-Dimensional Channel Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1975)