Journal of Fluids Engineering: Recent submissions
Now showing items 8801-8820 of 9024
-
Discussion: “Performance and Flow Regime of Annular Diffusers With Axial Turbomachine Discharge Inlet Conditions” (Adenubi, S. O., 1976, ASME J. Fluids Eng., 98, pp. 236–243)
(The American Society of Mechanical Engineers (ASME), 1976) -
Letter to the Editor commenting on “Editorial: On The Decline of U. S. Technology” (Dean, Jr., Robert C., 1976, ASME J. Fluids Eng., 98, p. 141)
(The American Society of Mechanical Engineers (ASME), 1976) -
Letter to the Editor commenting on “Solid Waste Disposal—Facts versus Fiction” (Alvarez, Ronald J., 1976, Mechanical Engineering)
(The American Society of Mechanical Engineers (ASME), 1976) -
Control of Free-Stream Turbulence by Means of Honeycombs: A Balance Between Suppression and Generation
(The American Society of Mechanical Engineers (ASME), 1976)The effects of honeycomb of different lengths on free-stream turbulence are studied in air with hot-wire anemometry and in water using hydrogen bubbles visualization. The honeycombs are viewed ... -
The Response of a Developed Turbulent Boundary Layer to Local Transverse Surface Motion
(The American Society of Mechanical Engineers (ASME), 1976)Measurements were obtained of the mean velocity, Reynolds stress tensor components and spectral distribution of turbulent energy in a boundary layer that was adjusting spatially from a collateral ... -
Losses in Radial Inflow Turbines
(The American Society of Mechanical Engineers (ASME), 1976)A study was conducted to determine experimentally and theoretically the losses in radial inflow turbine nozzles. Extensive experimental data were obtained to investigate the flow behavior in a ... -
Turbulent Boundary Layers on Centrifugal Compressor Blades: Prediction of the Effects of Surface Curvature and Rotation
(The American Society of Mechanical Engineers (ASME), 1976)A method for calculation of turbulent boundary layers on curved, rotating surfaces is presented, and the applicability of the method to the prediction of attached flow over compressor rotor ... -
Discussion: “Symmetrical Laminar Channel Flow With Wall Suction” (Gupta, B. K., and Levy, E. K., 1976, ASME J. Fluids Eng., 98, pp. 469–474)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Forces on Cylinders Near a Plane Boundary in a Sinusoidally Oscillating Fluid” (Sarpkaya, Turgut, 1976, ASME J. Fluids Eng., 98, pp. 499–503)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “A Finite-Element Method for Through Flow Calculations in Turbomachines” (Hirsch, Ch., and Warzee, G., 1976, ASME J. Fluids Eng., 98, pp. 403–414)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “A Direct Method of Calculating Through Separated Regions in Boundary Layer Flow” (Pletcher, Richard H., and Dancey, Clinton L., 1976, ASME J. Fluids Eng., 98, pp. 568–570)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Pressure Surge Propagation in Thick-Walled Conduits of Rectangular Cross Section” (Thorley, A. R. D., and Guymer, C., 1976, ASME J. Fluids Eng., 98, pp. 455–459)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “The Force Acting on a Particle and a Bubble in a Spherically Oscillating Inviscid Liquid” (Marmur, A., and Rubin, E., 1976, ASME J. Fluids Eng., 98, pp. 483–486)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Flow Interaction Near the Tail of a Body of Revolution—Parts 1 and 2” (Nakayama, A., Patel, V. C., and Landweber, L., 1976, ASME J. Fluids Eng., 98, pp. 531–546)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Experimental Results and Analysis of Flow in a Pneumatic Tube System During a Vehicle Transit” (Cudlin, J. J., and Harman, C. M., 1976, ASME J. Fluids Eng., 98, pp. 224–228)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Three-Dimensional Boundary-Layer Computation on the Stationary End-Walls of Centrifugal Turbomachinery” (Davis, W. R., 1976, ASME J. Fluids Eng., 98, pp. 431–441)
(The American Society of Mechanical Engineers (ASME), 1976) -
Shear Effects in Hot-Wire Measurements
(The American Society of Mechanical Engineers (ASME), 1976)When a circular cylinder is placed in a two-dimensional shear flow, a lift force is experienced by the cylinder. In the case of hot-wire measurements in the viscous sublayer, this will give ... -
Technology Status for Blade Flutter in Axial Turbomachinery
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Losses in Radial Inflow Turbines” (Khalil, I. M., Tabakoff, W., and Hamed, A., 1976, ASME J. Fluids Eng., 98, pp. 364–371)
(The American Society of Mechanical Engineers (ASME), 1976) -
Measured uw Stress Gradients in a Three-Dimensional Turbulent Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1976)