Journal of Fluids Engineering: Recent submissions
Now showing items 8781-8800 of 9024
-
Laser-Doppler Measurements in a Subsonic Jet Injected Into a Subsonic Cross Flow
(The American Society of Mechanical Engineers (ASME), 1976)The flow field of a small nitrogen jet (5 mm diameter) injected into a cross flow of air at a momentum-flux ratio of 16 was explored in the plane of the trajectory by means of a laser-Doppler ... -
Momentum Integral Solution of Developing Flow in an Annulus With a Rotating Inner Cylinder
(The American Society of Mechanical Engineers (ASME), 1976) -
Forces on Unstaggered Airfoil Cascades in Unsteady In-Phase Motion
(The American Society of Mechanical Engineers (ASME), 1976)Incompressible flow through an unstaggered cascade in general, unsteady, in-phase motion is considered. By methods of thin-airfoil theory, using the assumptions of wakes trailing back at the ... -
Flow Interaction Near the Tail of a Body of Revolution—Part 1: Flow Exterior to Boundary Layer and Wake
(The American Society of Mechanical Engineers (ASME), 1976)An iterative procedure for the calculation of the thick attached turbulent boundary layer near the tail of a body of revolution is presented. The procedure consists of the potential-flow ... -
Pressure Surge Propagation in Thick-Walled Conduits of Rectangular Cross Section
(The American Society of Mechanical Engineers (ASME), 1976)This paper discusses the propagation of pressure surge phenomena in liquids contained in thick-walled pipes and ducts of rectangular cross section. It is shown that the effects of shear forces ... -
Some Characteristics of Cavity Flow Past Cylindrical Inducers in a Venturi
(The American Society of Mechanical Engineers (ASME), 1976)The characteristic dimensions of the steady cavity and the shedding frequency of vortices behind six circular cylinders in a two-dimensional venturi have been studied. The normalized length and ... -
An Optimum Stepped Piston for Cylinders Working With Compressible Fluid
(The American Society of Mechanical Engineers (ASME), 1976)A stepped piston, enclosed within a tight circular cylinder of uniform bore and subjected to unequal upstream and downstream boundary pressures, is analyzed for the case of a compressible fluid. ... -
Symmetrical Laminar Channel Flow With Wall Suction
(The American Society of Mechanical Engineers (ASME), 1976)Entrance region solutions of the two-dimensional boundary layer equations are presented in terms of a convergent power series for steady, laminar, incompressible channel flow with uniform mass ... -
Static Characteristics of Shrouded Acoustically Controlled Turbulence Amplifiers
(The American Society of Mechanical Engineers (ASME), 1976)The static characteristics of shrouded, acoustically controlled turbulence amplifiers are investigated. The main variables are control sound pressure level and frequency, shroud diameter, gap length ... -
The Force Acting on a Particle and a Bubble in a Spherically Oscillating Inviscid Liquid
(The American Society of Mechanical Engineers (ASME), 1976)The force acting on a particle and a bubble in a spherically oscillating inviscid liquid is computed and proved to be directed toward the center of the spherical motion. The theoretical ... -
An In Vitro Study of Transendothelial Albumin Transport in a Steady State Pipe Flow at High Shear Rates
(The American Society of Mechanical Engineers (ASME), 1976)The effect of high wall shear rates on the uptake of 131 I-albumin by the arterial wall has been studied in vitro using common carotid arteries excised from anesthetized dogs and perfused ... -
Detailed Flow Investigations Within a High-Speed Centrifugal Compressor Impeller
(The American Society of Mechanical Engineers (ASME), 1976)Detailed accurate measurements of velocities, directions, and fluctuation intensities were performed with a newly developed laser velocimeter in the internal flow field of a radial discharge ... -
A Finite-Element Method for Through Flow Calculations in Turbomachines
(The American Society of Mechanical Engineers (ASME), 1976)A new method for the numerical solution of the meridional through-flow equations in an axial flow machine is presented based on the finite-element method. A rigorous derivation of the pitch-averaged ... -
Effects of System Rotation on the Performance of Two-Dimensional Diffusers
(The American Society of Mechanical Engineers (ASME), 1976)Experiments with incompressible flow are reported concerning the effects of Coriolis acceleration on flow separation and on separated flow in plane-wall diffusers of rectangular cross section. The ... -
Three-Dimensional Boundary-Layer Computation on the Stationary End-Walls of Centrifugal Turbomachinery
(The American Society of Mechanical Engineers (ASME), 1976)An integral entrainment computation technique is presented for the three-dimensional boundary-layer growth on the stationary end-walls of centrifugal turbomachinery. The analytical model assumes ... -
Signal Transit Velocities in a Turbulent Plane Jet
(The American Society of Mechanical Engineers (ASME), 1976)A turbulent jet is perturbed transverse to the flow direction by periodic pressure gradients near the nozzle exit. Transit velocities are defined in terms of the measured signal time delay for ... -
Laminar Compressible Flow Between Rotating Disks
(The American Society of Mechanical Engineers (ASME), 1976)An integral method is used to obtain a solution for laminar flow of a compressible Newtonian fluid between rotating disks. The solution method is based on a Galerkin approach to the solution ... -
The Suppression of Flow Separation by Sequential Wall Jets
(The American Society of Mechanical Engineers (ASME), 1976)The performance of many fluid flow devices is limited by the separation of the turbulent boundary layer. This separation may be suppressed or delayed by use of wall jets, raising questions ... -
Erratum: “Effect of Velocity Slip on the Burning Rate of Fuel Particles” (Journal of Fluids Engineering, 1975, 97, pp. 321–326)
(The American Society of Mechanical Engineers (ASME), 1976) -
Erratum: “Experimental Results and Analysis of Flow in a Pneumatic Tube System During a Vehicle Transit” (Journal of Fluids Engineering, 1976, 98, pp. 224–228)
(The American Society of Mechanical Engineers (ASME), 1976)