Journal of Fluids Engineering: Recent submissions
Now showing items 8741-8760 of 9024
-
Steam Flow Through Safety Valve Vent Pipes
(The American Society of Mechanical Engineers (ASME), 1976)The flow of steam through a safety valve vent pipe system has been analyzed to provide a design basis for sizing the pipe to prevent blowback of steam. The analysis is based upon the ... -
An Improvement in the Calculation of Turbulent Friction in Rectangular Ducts
(The American Society of Mechanical Engineers (ASME), 1976)Frictional pressure drop in rectangular ducts is examined. Using correspondence between theory and experiment in laminar flow as a means for acceptance of published data, turbulent flow data for ... -
Nonaxisymmetric Flow in the Narrow Gap Between a Rotating and a Stationary Disk
(The American Society of Mechanical Engineers (ASME), 1976)The flow between a rotating disk and a stationary disk, with nonaxisymmetric boundary conditions is studied. A flow field of this type exists in the narrow gap between the rotor and side ... -
An Analysis on the Flow in a Casing Induced by a Rotating Disk Using a Four-Layer Flow Model
(The American Society of Mechanical Engineers (ASME), 1976)An analytical study has been made to clarify the details of the flow between a rotating disk and a stationary casing side-wall with and without an axisymmetric inward through-flow. The flow ... -
A Study on Multielement Cascades and Airfoils
(The American Society of Mechanical Engineers (ASME), 1976)A critical review is presented on methods of surface distribution of singularities around multielement arifoils in plane potential flow analysis. The approach of piecewise constant distribution ... -
Experimental Results and Analysis of Flow in a Pneumatic Tube System During a Vehicle Transit
(The American Society of Mechanical Engineers (ASME), 1976)A pneumatic tube system suitable for transportation purposes is simulated in an experimental facility. The vehicle position, velocity and corresponding system pressures were obtained and are ... -
Discussion: “Study of Flow and Thrust in Nozzle-Flapper Valves” (Hayashi, S., Matsui, T., and Ito, T., 1975, ASME J. Fluids Eng., 97, pp. 39–50)
(The American Society of Mechanical Engineers (ASME), 1976) -
On The Decline of U. S. Technology
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Prediction of Turbulent Jets in Coflowing Quiescent Ambients” (Madni, I. K., and Pletcher, R. H., 1975, ASME J. Fluids Eng., 97, pp. 558–567)
(The American Society of Mechanical Engineers (ASME), 1976) -
Erratum: “Turbulent Mixing and Reacting Flow Characterization” (Journal of Fluids Engineering, 1975, 97, pp. 608–614)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Two-Dimensional Method for Calculating Separated Flow in a Centrifugal Impeller” (Sturge, D. P., and Cumpsty, N. A., 1975, ASME J. Fluids Eng., 97, pp. 581–597)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Choking and Mixing of Two Compressible Fluid Streams” (Otis, D. R., 1976, ASME J. Fluids Eng., 98, pp. 311–317)
(The American Society of Mechanical Engineers (ASME), 1976) -
Analysis of Finite Cylinders Rotating Within Moderate Clearance Ratios
(The American Society of Mechanical Engineers (ASME), 1976)The Navier-Stokes equations are examined here for the flow of an incompressible fluid contained between rotating eccentric cylinders of finite length and moderate clearance ratios. Based on a ... -
Discussion: “Performance and Flow Regime of Annular Diffusers With Axial Turbomachine Discharge Inlet Conditions” (Adenubi, S. O., 1976, ASME J. Fluids Eng., 98, pp. 236–242)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “A Study on Multielement Cascades and Airfoils” (Minassian, L. M., 1976, ASME J. Fluids Eng., 98, pp. 208–215)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Periodic Flow in a Wind Tunnel Produced by Rotating Shutters” (Charnay, G., and Mathieu, J., 1976, ASME J. Fluids Eng., 98, pp. 278–281)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Nonaxisymmetric Flow in the Narrow Gap Between a Rotating and a Stationary Disk” (Bein, M., Shavit, A., and Solan, A., 1976, ASME J. Fluids Eng., 98, pp. 217–223)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Turbulent Mixing of Coaxial Jets With Particular Reference to the Near-Exit Region” (Ribeiro, M. M., and Whitelaw, J. H., 1976, ASME J. Fluids Eng., 98, pp. 284–291)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Momentum Flux Development From Three-Dimensional Free Jets” (Narain, J. P., 1976, ASME J. Fluids Eng., 98, pp. 256–260)
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Fluid Mixing With Unequal Free-Stream Turbulence Intensities” (Mohammadian, S., Saiy, M., and Peerless, S. J., 1976, ASME J. Fluids Eng., 98, pp. 229–235)
(The American Society of Mechanical Engineers (ASME), 1976)