Journal of Fluids Engineering: Recent submissions
Now showing items 8721-8740 of 9024
-
Discussion: “Effects of the Axisymmetric Contraction Shape on Incompressible Turbulent Flow” (Hussain, A. K. M. F., and Ramjee, V., 1976, ASME J. Fluids Eng., 98, pp. 58–68)
(The American Society of Mechanical Engineers (ASME), 1976) -
Visualization of Secondary Flows in Planar Nozzles
(The American Society of Mechanical Engineers (ASME), 1976) -
Discussion: “Measurement of the Propagation of Long-Wavelength Disturbances Through Turbulent Flow in Tubes” (Margolis, D. L., and Brown, F. T., 1976, ASME J. Fluids Eng., 98, pp. 70–78)
(The American Society of Mechanical Engineers (ASME), 1976) -
Measurements of Velocity Wave Forms in the Dog Aorta
(The American Society of Mechanical Engineers (ASME), 1976)Hot film needle and catheter probes were used to measure the velocity waves in the dog aorta between the aortic valve and the iliac bifurcation. The forms of the waves were found to be of ... -
Periodic Flow in a Wind Tunnel Produced by Rotating Shutters
(The American Society of Mechanical Engineers (ASME), 1976)The periodic flow obtained in a wind tunnel test section by means of an upstream pulsator is investigated. The turbulence level in this section is quite small and the direction of the periodic ... -
Turbulent Mixing of Coaxial Jets With Particular Reference to the Near-Exit Region
(The American Society of Mechanical Engineers (ASME), 1976)Measurements, obtained with hot wire anemometry, are reported in a co-axiol jet flow where the inner and outer initial maximum velocities were the same. The hot-wire signal was processed with ... -
An Approximate Method for the Solution of a Class of Nonsimilar Laminar Boundary Layer Equations
(The American Society of Mechanical Engineers (ASME), 1976)An approximate method is developed for locally nonsimilar laminar boundary layer flows. This method is applicable to several boundary layer velocity problems where the nonsimilarity stems from ... -
Entry Flow in Curved Channels
(The American Society of Mechanical Engineers (ASME), 1976)Entry flow in curved channels is investigated by an approximate method analogous to that used by Pohlhausen in his treatment of boundary layer flows. Constant total pressure across the channel ... -
Choking and Mixing of Two Compressible Fluid Streams
(The American Society of Mechanical Engineers (ASME), 1976)The mixing of a supersonic with a subsonic stream is treated in a one-dimensional, ideal gas analysis to determine when the mixed flow can be supersonic and to reveal the relationship between ... -
A Note on the Two-Dimensional Cylinder Wake
(The American Society of Mechanical Engineers (ASME), 1976) -
Analysis of Turbulent Unseparated Flow in Subsonic Diffusers
(The American Society of Mechanical Engineers (ASME), 1976) -
A Transient Response Approximation for Noncircular Fluid Transmission Lines
(The American Society of Mechanical Engineers (ASME), 1976)A method is given for determining the transient response approximation for noncircular fluid transmission lines. The results are presented in terms of a characteristic frequency which depends ... -
Momentum Flux Development From Three-Dimensional Free Jets
(The American Society of Mechanical Engineers (ASME), 1976)The momentum-flux development from three-dimensional free jets has been investigated. The analysis is presented for free jets from circular, triangular, rectangular and elliptical orifices. The ... -
Fluid Mixing With Unequal Free-Stream Turbulence Intensities
(The American Society of Mechanical Engineers (ASME), 1976)The rate of mixing between parallel fluid streams depends on the turbulence intensity in each stream, and, if these turbulence levels are unequal, on whether the higher intensity occurs in the ... -
Potential Flow Solution for Crossflow Impingement of a Slot Jet on a Circular Cylinder
(The American Society of Mechanical Engineers (ASME), 1976)A closed-form solution has been obtained for the potential flow about a circular cylinder situated in an impinging slot jet. Among other results, the potential flow solution yields the free ... -
A Reynolds Stress Model for Turbulent Corner Flows—Part II: Comparisons Between Theory and Experiment
(The American Society of Mechanical Engineers (ASME), 1976)The applicability of the Reynolds stress model developed in Part I to fully developed rectangular duct flow is investigated. Two sets of experimental data are analyzed in order to prescribe a ... -
Performance and Flow Regime of Annular Diffusers With Axial Turbomachine Discharge Inlet Conditions
(The American Society of Mechanical Engineers (ASME), 1976)An experimental investigation of the flow regime and the performance of straight-core annular diffusers operating immediately downstream of an axial compressor was carried out. Features of the ... -
A Reynolds Stress Model for Turbulent Corner Flows—Part I: Development of the Model
(The American Society of Mechanical Engineers (ASME), 1976)A Reynolds stress model is proposed for modeling the local turbulence structure in flow along a streamwise corner. Initial discussion centers on present methods of predicting internal and extenal ... -
Assessment of Three-Dimensional Inviscid Effects in Turbomachinery Using Simple Models
(The American Society of Mechanical Engineers (ASME), 1976)The general objective of the investigation reported in this paper is to obtain a reliable understanding of the three-dimensional inviscid effects in axial flow turbomachinery. The calculation is ... -
The Dynamic Transfer Function for a Cavitating Inducer
(The American Society of Mechanical Engineers (ASME), 1976)Knowledge of the dynamic performance of pumps is essential for the prediction of transient behavior and instabilities in hydraulic systems; the necessary information is in the form of a transfer ...