Journal of Fluids Engineering: Recent submissions
Now showing items 8261-8280 of 9024
-
A Wall-Flow-Direction Probe for Use in Separating and Reattaching Flows
(The American Society of Mechanical Engineers (ASME), 1979)The measurement of the exceedingly unsteady behavior of nominally two-dimensional, turbulent flows in regions of separation and reattachment is facilitated by the development of a new instrument; ... -
Discussion: “An Experimental Investigation of Flow Unsteadiness Generated by Transitory Stall” (Smith, C. R., and Layne, J. L., 1979, ASME J. Fluids Eng., 101, pp. 181–185)
(The American Society of Mechanical Engineers (ASME), 1979) -
Effect of Nozzle Shape and Polymer Additives on Water Jet Appearance
(The American Society of Mechanical Engineers (ASME), 1979)The effects of shape parameters on the performance of water-jet nozzles discharging in air were investigated using a camera specially adapted for jet photography. The boundary-layer developing ... -
Discussion: “Effects of Additive Ejection on Lifting Hydrofoils” (Fruman, D. H., and Tulin, M. P., 1979, ASME J. Fluids Eng., 101, pp. 244–250)
(The American Society of Mechanical Engineers (ASME), 1979) -
Predictions of Induced Air Flows in Hollow Cone Sprays
(The American Society of Mechanical Engineers (ASME), 1979)The problem of hydrodynamic interaction between a hollow cone spray and the encompassing unbounded fluid has been formulated in terms of a set of partial and a set of ordinary differential ... -
Erratum: “Symmetric Sink Flow Between Parallel Plates” (Journal of Fluids Engineering, 1978, 100, pp. 477–484)
(The American Society of Mechanical Engineers (ASME), 1979) -
Laminar Flow of Suspensions in the Entrance Region of a Diffuser
(The American Society of Mechanical Engineers (ASME), 1979)An analytical investigation of the mechanics of deposition of fine particles in a two-dimensional diffuser from the diffuser to inlet to the point of separation has been made. The deposition ... -
Discussion: “Fluid Dynamic Excitation of Centrifugal Compressor Rotor Vibrations” (Thompson, W. E., 1978, ASME J. Fluids Eng., 100, pp. 73–78)
(The American Society of Mechanical Engineers (ASME), 1979) -
A Vortex Model of the Darrieus Turbine: An Analytical and Experimental Study
(The American Society of Mechanical Engineers (ASME), 1979)An aerodynamic prediction model has been formulated for two- and three-dimensional Darrieus turbines using a vortex lattice method of analysis. Experiments were conducted on a series of two-dimensional ... -
Estimation of Pressure Loss in Ring-Type Exit Chambers
(The American Society of Mechanical Engineers (ASME), 1979)A simple Borda-Carnot type of analysis is presented which enables an estimate to be made of the pressure loss in the exit chamber of an axial-flow turbomachine. Based upon the recent experimental ... -
Velocity Characteristics of a Confined Coaxial Jet
(The American Society of Mechanical Engineers (ASME), 1979)The velocity characteristics of a turbulent, confined, coaxial-jet flow have been determined by measurement and by the solution of conservation equations in differential form. The ratios of maximum ... -
A Comparison of Correction Methods Used in the Evaluation of Drag Coefficient Measurements for Two-Dimensional Rectangular Cylinders
(The American Society of Mechanical Engineers (ASME), 1979)This paper describes an experimental evaluation of available drag correction formulae and theories for blockage effects applicable to two-dimensional rectangular cylinders immersed in a low-turbulence ... -
Discussion: “A Hybrid Marching Integration Procedure for the Prediction of Two-Dimensional Supersonic Boundary Layers” (Issa, R. I., and Lockwood, F. C., 1977, ASME J. Fluids Eng., 99, pp. 205–212)
(The American Society of Mechanical Engineers (ASME), 1979) -
An Investigation of Pressure Transients in Viscoelastic Pipes
(The American Society of Mechanical Engineers (ASME), 1979)Calculated results based on a theoretical analysis of hydraulic transients in pipes taking into account the viscoelastic behavior of pipewall material are compared with experimental results. This ... -
Measurements Within Görtler Vortices
(The American Society of Mechanical Engineers (ASME), 1979)Local measurements of stream wise velocity component have been made in the laminar boundary layer on the concave surface of a water channel, supported by flow visualization. Details of the ... -
Discussion: “Predicted Secondary Flows in Triangular Array Rod Bundles” (Trupp, A. C., and Aly, A. M. M., 1979, ASME J. Fluids Eng., 101, pp. 354–362)
(The American Society of Mechanical Engineers (ASME), 1979) -
An Experimental Study of Flow Over a Rectangular Body
(The American Society of Mechanical Engineers (ASME), 1979)An experimental investigation has been performed to determine the surface pressure distribution on models of rectangular cross section in a two dimensional incompressible flow as a function of ... -
Turbulent Flow Over a Disk Normal to a Wall
(The American Society of Mechanical Engineers (ASME), 1979)Measurements have been taken of local mean velocities and turbulence intensities in an external separated flow situation in air using a forward, dual-scatter, laser Doppler anemometer. Frequency ... -
Inverse Design of Optimal Diffusers With Experimental Corroboration
(The American Society of Mechanical Engineers (ASME), 1979)The equations of motion for a turbulent boundary layer are formulated in an inverse manner and solved to provide the geometrical configuration of optimal two-dimensional diffusers with a distinct ... -
Two Dimensional Lateral Flow Past a Barrier
(The American Society of Mechanical Engineers (ASME), 1979)The well-known Schwarz-Christoffel transformation and the free streamline theory are used to solve the problem of flow past a lateral outlet housed in a two-dimensional conduit. The solution ...