Journal of Fluids Engineering: Recent submissions
Now showing items 8181-8200 of 9024
-
A Theoretical Study on Air Bubble Motion in a Centrifugal Pump Impeller
(The American Society of Mechanical Engineers (ASME), 1980)Equations of motion for air bubbles in a centrifugal pump impeller were obtained and solved numerically for a flow in a radial-flow-type impeller, and the results were compared with experiments. ... -
Flow Prediction in Rotating Ducts Using Coriolis-Modified Turbulence Models
(The American Society of Mechanical Engineers (ASME), 1980)A parabolic numerical analysis procedure has been used to predict the flow in a straight, radial rotating channel of rectangular cross-section, chosen as a simple model of an impeller passage. ... -
A Laser-Two-Focus (L2F) Velocimeter for Automatic Flow Vector Measurements in the Rotating Components of Turbomachines
(The American Society of Mechanical Engineers (ASME), 1980)Numerous results—most of them are published—have proved the applicability of the L2F-velocimeter to experimental studies of the complex compressor flow: e.g. the blade wakes and the shock-wave ... -
Discussion: “Three-Dimensional Supersonic Flow Through a Cascade of Twisted Flat Plates” (Grainger, C. F., 1980, ASME J. Fluids Eng., 102, pp. 338–343)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Flow Measurement in a Turbine Scroll” (Tabakoff, W., Sheoran, Y., and Kroll, K., 1980, ASME J. Fluids Eng., 102, pp. 290–296)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Frictional Resistance of Enclosed Rotating Cones With Superposed Throughflow” (Yamada, Y., and Ito, M., 1979, ASME J. Fluids Eng., 101, pp. 259–264)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Lower Mode Response of Circular Cylinders in Cross-Flow” (Durgin, W. W., March, P. A., and Lefebvre, P. J., 1980, ASME J. Fluids Eng., 102, pp. 183–190)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Discussion: ‘Two Dimensional Lateral Flow Past a Barrier’” (McNown, J. S., 1980, ASME J. Fluids Eng., 102, pp. 251–253)
(The American Society of Mechanical Engineers (ASME), 1980) -
Leslie S. G. Kovasznay
(The American Society of Mechanical Engineers (ASME), 1980) -
An Axial Flow Research Compressor Facility Designed for Flow Measurement in Rotor Passages
(The American Society of Mechanical Engineers (ASME), 1980)An axial-flow research compressor facility, which is designed for relative flow measurement, is described in this paper. The facility has a rotating-probe traverse mechanism which is capable of ... -
Discussion: “Supercavitating Cavity Observations by Means of Laser Velocimeter” (Oba, R., Ikohagi, T., and Yasu, S., 1980, ASME J. Fluid Eng., 102, pp. 433–438)
(The American Society of Mechanical Engineers (ASME), 1980) -
Wind Effects on Structures: An Introduction to Wind Engineering and Wind Forces in Engineering (2nd Edition)
(The American Society of Mechanical Engineers (ASME), 1980) -
Injection and Mixing in Turbulent Flow (Progress in Aeronautics and Astronautics, Vol. 68)
(The American Society of Mechanical Engineers (ASME), 1980) -
Applied Fluid Flow Measurement Fundamentals & Technology
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “An Analysis of Uniform Shear Flow Past a Porous Plate Attached to a Plane Surface” (Kiya, M., Arie, M., and Koshikawa, K., 1980, ASME J. Fluids Eng., 102, pp. 166–173)
(The American Society of Mechanical Engineers (ASME), 1980) -
Editorial
(The American Society of Mechanical Engineers (ASME), 1979) -
Editorial
(The American Society of Mechanical Engineers (ASME), 1979) -
Discussion: “A Note on the Phase Relationships Involved in the Whirling Instability in Tube Arrays” (Savkar, S. D., 1977, ASME J. Fluids Eng., 99, pp. 727–731)
(The American Society of Mechanical Engineers (ASME), 1979) -
Discussion: “The Computation of Optimum Pressure Recovery in Two-Dimensional Diffusers” (Ghose, S., and Kline, S. J., 1978, ASME J. Fluids Eng., 100, pp. 419–426)
(The American Society of Mechanical Engineers (ASME), 1979) -
REVIEW—Unsteady Boundary Layers, Separated and Attached
(The American Society of Mechanical Engineers (ASME), 1979)Unsteady boundary layers are investigated very actively today as a part of the effort to fully understand and calculate unsteady flows and their applications. As a result a number of review ...