Journal of Fluids Engineering: Recent submissions
Now showing items 8121-8140 of 9024
-
Shear Layer Transition and the Sharp-Edged Orifice
(The American Society of Mechanical Engineers (ASME), 1980)The present experiments provide information about free shear layer transition to turbulence and the associated three-dimensional behavior patterns of vortex growth and breakdown. The free shear ... -
Discussion: “Investigations of Pulsating Turbulent Pipe Flow” (Kirmse, R. E., 1979, ASME J. Fluids Eng., 101, p. 436)
(The American Society of Mechanical Engineers (ASME), 1980) -
Vortex Shedding From Two Circular Cylinders in Staggered Arrangement
(The American Society of Mechanical Engineers (ASME), 1980)The frequency of vortex shedding from two circular cylinders of the same diameter in staggered arrangement is experimentally investigated at a Reynolds number of 1.58 × 104 . This Reynolds ... -
Discussion: “Pressure Pulse Propagation in Two-Component Slug Flow” (Martin, C. Samuel, and Padmanabhan, M., 1979, ASME J. Fluids Eng., 101, pp. 44–52)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “A Fundamental Criterion for the Application of Rotor Casing Treatment” (Greitzer, E. M., et al., 1979, ASME J. Fluids Eng., 101, p. 237)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “A Note on the Phase Relationships Involved in the Whirling Instability in Tube Arrays” (Savkar, S. D., 1977, ASME J. Fluids Eng., 99, pp. 727–731)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “On Vortex Wind Power” (So, Ronald M. C., 1978, ASME J. Fluids Eng., 100, pp. 79–82)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Griffith Diffusers” (Yang, Tah-teh, and Nelson, C. D., 1979, ASME J. Fluids Eng., 101, p. 473)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Viscous Liquid Films in Nonradial Rotating Pipes[1]” (Dakin, J. T., 1980, ASME J. Fluids Eng., 102, pp. 231–235)
(The American Society of Mechanical Engineers (ASME), 1980) -
Combined Simultaneous Flow Visualization/Hot-Wire Anemometry for the Study of Turbulent Flows
(The American Society of Mechanical Engineers (ASME), 1980)The measurement of coherent motions in turbulent and unsteady flows is discussed. A technique which discriminates these motions based upon the patterns they create by scattering light from a ... -
Discussion: “Two Dimensional Lateral Flow Past a Barrier” (Ramamurthy, A. S., and Carballada, B. L., 1979, ASME J. Fluids Eng., 101, p. 449)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Turbulent Flow Measurements by Laser-Doppler Anemometry in Motored Piston-Cylinder Assemblies” (Morse, A. P., Whitelaw, J. H., and Yianneskis, M., 1979, ASME J. Fluids Eng., 101, pp. 208–216)
(The American Society of Mechanical Engineers (ASME), 1980) -
An Analysis of Uniform Shear Flow Past a Porous Plate Attached to a Plane Surface
(The American Society of Mechanical Engineers (ASME), 1980)The wake-source model of Koo and James was extended to the case of a two-dimensional porous plate attached to a plane surface along which a turbulent boundary layer developed. The approaching ... -
Discussion: “Predicted and Measured Pressure Drop in Parallel Plate Rotary Regenerators” (Maclain-Cross, I. L., and Ambrose, C. W., 1980, ASME J. Fluids Eng., 102, pp. 59–63)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Shear Layer Transition and the Sharp-Edged Orifice” (Clark, J. A., and Kit, Lam, 1980, ASME J. Fluids Eng., 102, pp. 219–222)
(The American Society of Mechanical Engineers (ASME), 1980) -
Flow Meters: A Basic Source-Book for Users
(The American Society of Mechanical Engineers (ASME), 1980) -
An Increase in Base Pressure by Polymer Solutions Added to Separated Shear Layers
(The American Society of Mechanical Engineers (ASME), 1980)The change in the base pressure of a semicircular cylinder whose round side faced to the approaching stream was experimentally studied when the aqueous solutions of polyethyleneoxide (PEO) and ... -
Discussion: “Multidimensional Fluid Transients by Latticework” (Wylie, E. B., and Streeter, V. L. 1980, ASME J. Fluid Eng., 102, pp. 203–209)
(The American Society of Mechanical Engineers (ASME), 1980) -
Discussion: “Vortex Shedding From Two Circular Cylinders in Staggered Arrangement” (Kiya, M., Arie, M., Tamura, H., and Mori, H., 1980, ASME J. Fluids Eng., 102, pp. 166–171)
(The American Society of Mechanical Engineers (ASME), 1980) -
Review—Bluff Body Flows Applicable to Vehicle Aerodynamics
(The American Society of Mechanical Engineers (ASME), 1980)This paper attempts to review those aspects of bluff body aerodynamics that are relevant to the understanding of vehicle flows. Vehicles often have complex body shapes and are influenced by ...