Journal of Fluids Engineering: Recent submissions
Now showing items 7841-7860 of 9024
-
A Set of Instruments Useful for Liquid Quality Control During Cavitation Research
(The American Society of Mechanical Engineers (ASME), 1982)It is well-accepted by investigators of cavitation phenomena that undissolved and dissolved gas content in the liquid used affect the onset and type of cavitation in many cases. That is why ... -
Flow Split Relationships in Two-Phase Parallel Channel Flows
(The American Society of Mechanical Engineers (ASME), 1982)The observed flow combinations through the channels were: cocurrent upflow in both channels, cocurrent upflow in one and countercurrent flow in the other channel, and cocurrent upflow in one ... -
Plane Strain Fracture Toughness Measurements of High Strength Steels
(The American Society of Mechanical Engineers (ASME), 1963) -
A Controlled Buoyant Jet for Enhancing Stratification in a Liquid Storage Tank
(The American Society of Mechanical Engineers (ASME), 1982)An inlet manifold is described for introducing liquid of arbitrary temperature into a tank without destroying pre-existing stratification. This manifold may be described as a controlled, buoyant ... -
Non-Newtonian Liquid Blade Coating Process
(The American Society of Mechanical Engineers (ASME), 1982)A blade coating process for non-Newtonian liquids is presented using different air pressure applied at the inlet and the exit of the coating gap. The system consists of a coating blade to ... -
Discussion: “An Experimental Evaluation of Drag Coefficient for Rectangular Cylinders Exposed to Grid Turbulence” (Courchesne, J., and Laneville, A., 1982, ASME J. Fluids Eng., 104, pp. 523–527)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “New Skin Friction and Entrainment Correlations for Turbulent Boundary Layers” (Ferziger, J. H., Lyrio, A. A., and Bardina, J. G., 1982, ASME J. Fluids Eng., 104, pp. 537–540)
(The American Society of Mechanical Engineers (ASME), 1982) -
Erratum: “Flow Aerodynamic Modeling of an MHD Swirl Combustor: Calculation and Experimental Verification” (Journal of Fluids Engineering, 1982, pp. 385–392)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “A Controlled Buoyant Jet for Enhancing Stratification in a Liquid Storage Tank” (Gari, H. N., and Loehrke, R. I., 1982, ASME J. Fluids Eng., 104, pp. 475–481)
(The American Society of Mechanical Engineers (ASME), 1982) -
Capped End, Thin-Wall Tube Creep-Rupture Behavior for Type 316 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1963)The creep-rupture behavior of 34 capped end, thin-wall tubular specimens was correlated with results for 54 uniaxial tensile specimens in tests at 1350 F, 1500 F, and 1650 F. Basic tests ... -
Scale Effects in the Dynamic Transfer Functions for Cavitating Inducers
(The American Society of Mechanical Engineers (ASME), 1982)Dynamic transfer functions for two cavitating inducers of the same geometry but different size are presented, compared, and discussed. The transfer functions for each inducer indicate similar ... -
Discussion: “Draining of Tanks With Submerged Outlets or Without Vacuum Relief” (Dodge, F. T., and Bowles, E. B., 1982, ASME J. Fluids Eng., 104, pp. 67–71)
(The American Society of Mechanical Engineers (ASME), 1982) -
Fluid Dynamics of Inducers—A Review
(The American Society of Mechanical Engineers (ASME), 1982)The objective of this paper is to review the experimental and analytical investigations on the fluid dynamic aspects of noncavitating inducers. Various analyses available for the prediction of ... -
An Album of Fluid Motion
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “Discharge Coefficient for Venturi Flowmeter With Short Laying Length” (Inoue, Masahiro, 1982, ASME J. Fluids Eng., 104, pp. 463–467)
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion: “New Method for Monitoring and Correlating Cavitation Noise to Erosion Capability” (De, M. K., and Hammitt, F. G., 1982, ASME J. Fluids Eng., 104, pp. 434–441)
(The American Society of Mechanical Engineers (ASME), 1982) -
Effects of the Transient Period in Evaluating Rotating Disk Tests Under Creep Conditions
(The American Society of Mechanical Engineers (ASME), 1963) -
Advances in Transport Processes (Vols. I and II)
(The American Society of Mechanical Engineers (ASME), 1982) -
How to Write and Publish Engineering Papers and Reports
(The American Society of Mechanical Engineers (ASME), 1982) -
Annulus Wall Boundary Layers in Axial Compressor Stages
(The American Society of Mechanical Engineers (ASME), 1963)An analytical and experimental study is made of the development of secondary vorticities through the successive blade rows of a turbomachine. Whereas in cascade experiments the streamwise vorticity ...