Journal of Fluids Engineering: Recent submissions
Now showing items 7681-7700 of 9024
-
Pressure Field Generated by Nonspherical Bubble Collapse
(The American Society of Mechanical Engineers (ASME), 1983)The method of matched asymptotic expansions is used to investigate the behavior of a collapsing bubble near a solid wall. Cases are studied in which the ratio ε between the initial spherical ... -
Discussion: “Gas Flow Resistance Measurements Through Packed Beds at High Reynolds Numbers” (Jones, D. P., and Krier, H., 1983, ASME J. Fluids Eng., 105, pp. 168–172)
(The American Society of Mechanical Engineers (ASME), 1983) -
On the Skin Friction Coefficient for a Fully Rough Flat Plate
(The American Society of Mechanical Engineers (ASME), 1983)A comparison of the Prandtl-Schlichting formula for skin friction of a fully rough plate with recently obtained experimental data shows an average error of 17.5 percent. It is suggested that ... -
Discussion: “Simple and Explicit Formulas for the Friction Factor in Turbulent Pipe Flow” (Haaland, S. E., 1983, ASME J. Fluids Eng., 105, pp. 89–90)
(The American Society of Mechanical Engineers (ASME), 1983) -
Discussion: “Investigation of Wall Induced Modifications to Vortex Shedding From a Circular Cylinder” (Angrilli, F., Bergamaschi, S., and Cossalter, V., 1982, ASME J. Fluids Eng., 104, pp. 518–522)
(The American Society of Mechanical Engineers (ASME), 1983) -
The Effect of Free-Stream Turbulence on Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1983)Mean flow measurements, and some turbulence measurements, have been made in a two-dimensional incompressible constant-pressure (“flat plate”) turbulent boundary layer beneath a nearly homogeneous ... -
Toward Attenuation of Self-Sustained Oscillations of a Turbulent Jet Through a Cavity
(The American Society of Mechanical Engineers (ASME), 1983)Several attenuation configurations are assessed, involving the following concepts: generating streamwise vorticity, dephasing the azimuthal coherence of the jet, and reducing rigidity of the jet ... -
The Effect of Transverse Curvature on the Drag and Vortex Shedding of Elongated Bluff Bodies at Low Reynolds Number
(The American Society of Mechanical Engineers (ASME), 1983)This paper establishes the drag characteristics of finite cylinders of aspect ratio 1, 4, 10 and 100 for Reynolds numbers less than 1000 including the viscous regime. The effect of the drag ... -
Laminar Flow in the Entrance Region of Elliptical Ducts
(The American Society of Mechanical Engineers (ASME), 1983)A closed-form analytical solution is developed to hitherto unsolved problem of steady laminar flow of a Newtonian fluid in the entrance region of elliptical ducts. The analysis is based on the ... -
The Basic Aerodynamics of Floatation
(The American Society of Mechanical Engineers (ASME), 1983)The original derivation of the basic theory governing the aerodynamics of both hovercraft and modern floatation ovens, requires the validity of some extremely crude assumptions. However, the basic ... -
Studies of Flows Through N-Sequential Orifices
(The American Society of Mechanical Engineers (ASME), 1983)Critical mass flux and axial pressure profile data for fluid nitrogen are presented for N = 20, 15, 10, and 7 N-sequential-orifice-inlet configurations uniformly spaced at 15.5 cm. These data ... -
Analysis of Turbulent Gas-Solid Suspension Flow in a Pipe
(The American Society of Mechanical Engineers (ASME), 1983)The mixing length theory is extended to close the relevant momentum equations for two-phase turbulent flow at a first-order closure level. It is assumed that the mass fraction of the particles ... -
Laminar Flow in a Porous Tube
(The American Society of Mechanical Engineers (ASME), 1983)It is shown that an axisymmetric solution of the Navier-Stokes equations can be obtained for potential flow superimposed on Poiseuille flow. The result is used here to obtain a fully developed ... -
Discussion: “Pressure Field Generated by Nonspherical Bubble Collapse” (Chahine, G. L., and Bovis, A. G., 1983, ASME J. Fluids Eng., 105, pp. 356–362)
(The American Society of Mechanical Engineers (ASME), 1983) -
Near-Wall Similarity in a Shear-Driven Three-Dimensional Turbulent Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1983)Ten of eleven proposed three-dimensional similarity models identified in the literature are evaluated with direct wall shear, velocity field, and pressure gradient data from a three-dimensional ... -
Discussion: “LDV Measurements Near a Vortex Shedding Strut Mounted in a Pipe” (Yeh, T. T., Robertson, B., and Mattar, W. M., 1983, ASME J. Fluids Eng., 105, pp. 185–196)
(The American Society of Mechanical Engineers (ASME), 1983) -
Blade Boundary Layer Effect on Turbine Erosion and Deposition
(The American Society of Mechanical Engineers (ASME), 1983)As an extension to the inviscid gas flow particle trajectory model presented in earlier papers, a complementary model has been developed to establish the effect of the blade boundary layer on ... -
Discussion: “Interference Between Two Circular Cylinders of Finite Height Vertically Immersed in a Turbulent Layer” (Taniguchi, S., Sakamoto, H., and Arie, M., 1982, ASME J. Fluids Eng., 104, pp. 529–536)
(The American Society of Mechanical Engineers (ASME), 1983) -
Discussion: “The Effect of Transverse Curvature on the Drag and Vortex Shedding of Elongated Bluff Bodies at Low Reynolds Number” (Monson, D. R., 1983, ASME J. Fluids Eng., 105, pp. 308–318)
(The American Society of Mechanical Engineers (ASME), 1983) -
A Review of Near-Wall Similarity Models in Three-Dimensional Turbulent Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1983)Eleven near-wall similarity models for three-dimensional turbulent boundary layers which have been identified in the literature are reviewed. Each model summary includes a brief review of its ...