Journal of Fluids Engineering: Recent submissions
Now showing items 7661-7680 of 9024
-
Discussion: “Modification of Vortex Shedding in the Synchronization Range” (Zdravkovich, M. M., 1982, ASME J. Fluids Eng., 104, pp. 513–517)
(The American Society of Mechanical Engineers (ASME), 1983) -
Fluid Mechanics in Crystal Growth—The 1982 Freeman Scholar Lecture
(The American Society of Mechanical Engineers (ASME), 1983) -
Boundary-Layer Development on a Circular Cylinder With Ribs
(The American Society of Mechanical Engineers (ASME), 1983)An integral method for the calculation of the boundary layer development on a circular cylinder with external meridional ribs is presented. The calculation method, which takes into account the ... -
Effect of Tumbling and Burning on the Drag of Bluff Objects
(The American Society of Mechanical Engineers (ASME), 1983)The drag on various tumbling, nonburning wooden plates, cubes, rods, and wood chips was determined by measuring the free-fall velocity. The drag coefficient was reduced by a factor of 0.46 to ... -
Aerodynamic Studies on Swirled Coaxial Jets From Nozzles With Divergent Quarls
(The American Society of Mechanical Engineers (ASME), 1983)The aerodynamic characteristics of strongly swirled coaxial jets issuing from a divergent nozzle into stagnant-air surroundings have been studied. Maps of the central reverse-flow zone and detailed ... -
LDV Measurements Near a Vortex Shedding Strut Mounted in a Pipe
(The American Society of Mechanical Engineers (ASME), 1983)The velocity field around vortex shedding strut mounted in a circular pipe has been in detail with a laser Doppler velocimeter (LDV) at a pipe Reynolds number equal to 90,000. The instantaneous ... -
Gas Flow Resistance Measurements Through Packed Beds at High Reynolds Numbers
(The American Society of Mechanical Engineers (ASME), 1983)This research study indicates that the classical Reynolds number dependency of the coefficient of drag for gases forced into packed beds is not correct at high Reynolds numbers. Care must also ... -
Flow in a Rectangular Diffuser With Local Flow Detachment in the Corner Region
(The American Society of Mechanical Engineers (ASME), 1983)An experimental study was conducted in order to examine the nature of flow within a high-inlet-aspect-ratio rectangular diffuser with locally detached flow in the corner region, but attached ... -
Discussion: “Three-Dimensional Body-Fitted Coordinates for Turbomachine Applications” (Camarero, R., and Reggio, M., 1983, ASME J. Fluids Eng., 105, pp. 76–82)
(The American Society of Mechanical Engineers (ASME), 1983) -
Interaction of an Acoustic Disturbance and a Two-Dimensional Turbulent Jet: Experimental Data
(The American Society of Mechanical Engineers (ASME), 1983)An experimental study was performed to determine the effects a periodic acoustic disturbance had upon a two-dimensional turbulent jet in both the initial and similarity regions. Correlation and ... -
Discussion: “Non-Newtonian Liquid Blade Coating Process” (Hwang, S. S., 1982, ASME J. Fluids Eng., 104, pp. 469–474)
(The American Society of Mechanical Engineers (ASME), 1983) -
Artificially Thickened Turbulent Boundary Layers for Studying Heat Transfer and Skin Friction on Rough Surfaces
(The American Society of Mechanical Engineers (ASME), 1983)Thermal and hydrodynamic characteristics of boundary layers developing over uniform spheres roughness with momentum thicknesses as large as 1.43 cm are presented. To obtain thick hydrodynamic ... -
Pressure Fluctuations on the Surface of Two Circular Cylinders in Tandem Arrangement
(The American Society of Mechanical Engineers (ASME), 1983)The fluctuating pressures on the surface of two circular cylinders of the same diameter in tandem arrangement were measured in the upper subcritical regime to obtain the distributions of their ... -
A Remote Laser-Probe System for Velocity and Temperature Measurements
(The American Society of Mechanical Engineers (ASME), 1983)This paper demonstrates the feasibility of simultaneously making velocity and temperature measurements by the combined use of a laser Doppler velocimeter and coherent anti-Stokes Raman scattering. ... -
Effects of Turbulence on the Pressure Distribution Around a Square Cylinder and Possibility of Reduction
(The American Society of Mechanical Engineers (ASME), 1983) -
Development of Three-Dimensional Turbulent Boundary Layer in an Axially Rotating Pipe
(The American Society of Mechanical Engineers (ASME), 1983)The time-mean velocities and turbulent fluctuations inside the turbulent boundary layers which developed in an axially rotating pipe were measured in the case where an undeveloped flow with a ... -
The Flow States of Liquid Through Two Series-Connected Diffusers Subject to Cavitation
(The American Society of Mechanical Engineers (ASME), 1983)A “diffuser” is a venturi-like element with a well-formed contraction followed by a small-angle diffuser. When liquid flows through two diffusers connected in series various flow states are ... -
Discussion: “Pressure Fluctuations on the Surface of Two Circular Cylinders in Tandem Arrangement” (Arie, M., Kiya, M., Moriya, M., and Mori, H., 1983, ASME J. Fluids Eng., 105, pp. 161–166)
(The American Society of Mechanical Engineers (ASME), 1983) -
The Collapse of a Gas Bubble Attached to a Solid Wall by a Shock Wave and the Induced Impact Pressure
(The American Society of Mechanical Engineers (ASME), 1983)An experimental study was made on the collapse of a gas bubble attached to a solid wall by a shock wave. The collapse process of the bubble and the induced impact wall pressure were measured ... -
Discussion: “Effects of Surface Solidification on the Stability of Multilayered Liquid Films” (Lin, S. P., 1983, ASME J. Fluids Eng., 105, pp. 119–121)
(The American Society of Mechanical Engineers (ASME), 1983)