Journal of Fluids Engineering: Recent submissions
Now showing items 6761-6780 of 9024
-
Bending of Thick Steel Plates
(The American Society of Mechanical Engineers (ASME), 1965)The surface strains on an initially flat plate bent to a cylindrical shape are considered and compared to the biaxial rupture strain limit of the material. A procedure for predicting the ... -
Low Cycle Fatigue Evaluation of Inconel 713C and Waspaloy
(The American Society of Mechanical Engineers (ASME), 1965)Completely reversed axial fatigue results are reported for Waspaloy and Inconel 713C at room temperature. Fatigue strength and ductility are evaluated using power functions of the fatigue life. ... -
Effect of Composition and Microstructure on the Low Cycle Fatigue Strength of Structural Steels
(The American Society of Mechanical Engineers (ASME), 1965)In a number of studies of data obtained from fatigue tests on various materials it has been shown that the number of cycles to failure is related to the strain range by a relationship of ... -
Discussion: “An Investigation Into the Performance of Two ISA Metering Nozzles of Finite and Zero Area Ratio” (Soundranayagam, S., 1965, ASME J. Basic Eng., 87, pp. 525–529)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Significance of the Vortex Breakdown Phenomenon” (Benjamin, T. B., 1965, ASME J. Basic Eng., 87, pp. 518–522)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Step Responses of Liquid Lines With Frequency-Dependent Effects of Viscosity” (Brown, F. T., and Nelson, S. E., 1965, ASME J. Basic Eng., 87, pp. 504–510)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Effect of Surface Roughness on Cavitation Performance of Hydrofoils—Report 1” (Numachi, F., Ōba, R., and Chida, I., 1965, ASME J. Basic Eng., 87, pp. 495–502)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Laminar Boundary Layers and Their Separation From Curved Surfaces” (Massey, B. S., and Clayton, B. R., 1965, ASME J. Basic Eng., 87, pp. 483–493)
(The American Society of Mechanical Engineers (ASME), 1965) -
An Effect of Air Content on the Occurrence of Cavitation
(The American Society of Mechanical Engineers (ASME), 1960)The simultaneous occurrence of vaporous and gaseous cavitation on hydrofoils is considered. The experimental results show that gaseous cavitation occurs at much higher ambient pressures than that ... -
Discussion: “Pressure Surges in Magnetoviscous Flow” (Young, F. J., and Rouleau, W. T, 1965, ASME J. Basic Eng., 87, pp. 478–482)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Distortion of Short Pulses in Tapered Tube Pulse Transformers. Part II–Viscous Liquid’” (Rouleau, W. T., and Young, F. J., 1965, ASME J. Basic Eng., 87, pp. 471–476)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Initial Phases of Damage to Test Specimens in a Cavitating Venturi” (Hammitt, F. G., Barinka, L. L., Robinson, M. J., Pehlke, R. D., and Siebert, C. A., 1965, ASME J. Basic Eng., 87, pp. 453–463)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “The Reflection of Waterhammer Pressure Waves From Minor Losses” (Contractor, D. N., 1965, ASME J. Basic Eng., 87, pp. 445–451)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Primary Creep Design of Thick Tubes” (Smith, E. M., 1965, ASME J. Basic Eng., 87, pp. 379–383)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Biaxial Brittle Fracture Tests” (Manjoine, M. J., 1965, ASME J. Basic Eng., 87, pp. 293–298)
(The American Society of Mechanical Engineers (ASME), 1965) -
Magnetohydrodynamic Squeeze Film Bearings
(The American Society of Mechanical Engineers (ASME), 1965)A theoretical analysis is given for squeeze film bearings which use an electrically conducting fluid, such as a liquid metal, as the lubricant and which are in the presence of a magnetic ... -
Lubrication Review: A Digest of the Literature for 1963
(The American Society of Mechanical Engineers (ASME), 1965)In this review the developments in the fields of lubricants, friction, and bearing materials have been summarized by various authorities in each particular field. The review covers the period ... -
Calculation of Wear Rate
(The American Society of Mechanical Engineers (ASME), 1965)This paper contains exhaustive analytical data on factors contributing to wear. The wear of a deformed body interacting with an absolutely rigid rough solid is considered. It is believed that ... -
Contributions to the Determination of the Real Clearance in Sliding Bearings
(The American Society of Mechanical Engineers (ASME), 1965)When the bearing is running, its clearance is no longer equal to the initial one, as a result of the thermal regime and load. This paper presents a calculation method which takes into ... -
The Magnetohydrodynamic Parallel Plate Slider Bearing
(The American Society of Mechanical Engineers (ASME), 1965)The effect of a nonuniform applied magnetic field on the operation of a parallel plate slider bearing is investigated analytically. It is found that the optimum magnetic field profile is a ...