Journal of Fluids Engineering: Recent submissions
Now showing items 2161-2180 of 9024
-
Discussion: “Natural Breakdown of Planar Jets” (Rockwell, D. O., and Niccolls, W. O., 1972, ASME J. Basic Eng., 94, pp. 720–728)
(The American Society of Mechanical Engineers (ASME), 1972) -
Two New ASME Journals Announced: Journal of Basic Engineering to be Discontinued
(The American Society of Mechanical Engineers (ASME), 1972) -
Discussion: “Effects of Specimen Size and Notch Acuity on the Brittle Fracture Strength of a Heat-Treated Steel” (Yukawa, S., and McMullin, J. G., 1961, ASME J. Basic Eng., 83, pp. 541–544)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Application of a Cumulative Damage Concept to Fatigue” (Gatts, R. R., 1961, ASME J. Basic Eng., 83, pp. 529–534)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Bursting of Tubular Specimens by Gaseous Detonation” (Randall, P. N., and Ginsburgh, I., 1961, ASME J. Basic Eng., 83, pp. 519–527)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Effect of Cell Geometry on the Shear Modulus and on Density of Sandwich Panel Cores” (Chang, Chieh C., and Ebcioglu, Ibrahim K., 1961, ASME J. Basic Eng., 83, pp. 513–517)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Effect of Combined Stress on Yield and Fracture Behavior of Zircaloy-2” (Mehan, R. L., 1961, ASME J. Basic Eng., 83, pp. 499–508)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Tensile Properties of AISI Types 304 and 347 Stainless Steels at Moderate Temperatures for Section Sizes Ranging From Bars to Extremely Large Forgings” (Pryle, W. H., and Wessel, E. T., 1961, ASME J. Basic Eng., 83, pp. 489–498)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Short-Time Tensile Properties of Type 316 Stainless Steel at Very High Temperatures” (Gibbs, T. W., and Wyatt, H. W., 1961, ASME J. Basic Eng., 83, pp. 481–488)
(The American Society of Mechanical Engineers (ASME), 1961) -
Localization of Flow Separation and Transition Over a Pitching NACA0012 Airfoil at Transitional Reynolds Numbers Using Hot Films
(The American Society of Mechanical Engineers (ASME), 2015)Separation and transition of flow over a pitching airfoil at transitional Reynolds Number are analyzed experimentally. The method is based on a windowed correlation between hotfilm sensor signals taken simultaneously or ... -
Semi Empirical Study of Water Flow Through Vortex Triodes and Performance Optimization
(The American Society of Mechanical Engineers (ASME), 2015)A study was carried out to evaluate behavior and performance of vortex triodes. In particular, the study investigated the geometries and operating conditions which minimize the control flow capable of intercepting the ... -
Investigation in the Near Field of a Row of Interacting Jets
(The American Society of Mechanical Engineers (ASME), 2015)Multiple interacting jets (confluent jets) are employed in many engineering applications, and the significant design factors must be investigated. Computational fluid dynamics (CFD) is used to numerically predict the flow ... -
Effect of Slip on Circulation Inside a Droplet
(The American Society of Mechanical Engineers (ASME), 2015)Internal recirculation in a moving droplet, enforced by the presence of fluid–fluid interfaces, plays an important role in several dropletbased microfluidic devices as it could enhance mixing, heat transfer, and chemical ... -
Aerodynamic Analysis of a Passenger Car at Yaw Angle and Two Vehicle Platoon
(The American Society of Mechanical Engineers (ASME), 2015)Experimental and computational studies were performed to study the drag forces and the pressure distributions of a onefifth scale model FIAT Linea at increasing yaw angle and twovehicle platoon. Experiments were performed ... -
Optimizing Jets for Active Control of Wake Refinement for Ground Vehicles
(The American Society of Mechanical Engineers (ASME), 2015)The present study investigates active drag reduction of an Ahmed body with a rear slant angle of 25 deg. The drag is reduced by implementing slot jets on the rear slant and rear surface of the Ahmed body. Transient ... -
Wingtip Vortex Control Via Tip Mounted Half Delta Wings of Different Geometric Configurations
(The American Society of Mechanical Engineers (ASME), 2015)The control of the tip vortex, generated by a rectangular NACA 0012 wing, via tipmounted halfdelta wings (HDWs), of different slendernesses خ›, root chords cr, and deflections خ´, was investigated experimentally at ... -
Numerical and Experimental Investigation of Tip Leakage Vortex Cavitation Patterns and Mechanisms in an Axial Flow Pump
(The American Society of Mechanical Engineers (ASME), 2015)The tip leakage vortex (TLV) cavitating flow in an axial flow pump was simulated based on an improved shear stress transport (SST) kد‰ turbulence model and the homogeneous cavitation model. The generation and dynamics of ... -
Aerodynamic Effects of Inclined Portals on the Initial Compression Wave Generated by a High Speed Train Entering a Tunnel
(The American Society of Mechanical Engineers (ASME), 2015)The micropressure wave radiated from a tunnel exit is one of the environmental problems which can be investigated from the temporal pressure gradient of the compression wave. The effects of inclined portals on the initial ... -
Shared Memory Parallelization for Two Way Coupled Euler–Lagrange Modeling of Cavitating Bubbly Flows
(The American Society of Mechanical Engineers (ASME), 2015)Cavitating and bubbly flows are encountered in many engineering problems involving propellers, pumps, valves, ultrasonic biomedical applications, etc. In this contribution, an openmp parallelized Euler–Lagrange model of ... -
A Systematical Study of the Influence of Blade Length, Blade Width, and Side Channel Height on the Performance of a Side Channel Pump
(The American Society of Mechanical Engineers (ASME), 2015)Two modular side channel pump models have been investigated both numerically and experimentally. For both modular designs, different side channels and impellers could be studied, with the aim to get information about the ...