Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7681-7700 of 7723
-
Nonlinear Stress Analysis of Vertical-Axis Wind Turbine Blades
(The American Society of Mechanical Engineers (ASME), 1975)A Darrieus-type vertical-axis wind turbine has been proposed as an alternate to conventional horizontal axis, propeller-type machines. An advantage is that the blades will be primarily in tension, ... -
Large Displacement Matrix Analysis of Elastic/Viscoplastic, Plane Frame Structures
(The American Society of Mechanical Engineers (ASME), 1975)Within the framework of lumped mass/elementary beam theory, a large displacement matrix analysis of elastic/perfectly viscoplastic plane frame structures undergoing primarily flexural deformations ... -
A Technique for Determining Damping Values and Damper Locations in Multi-Degree-of-Freedom Systems
(The American Society of Mechanical Engineers (ASME), 1975)In complicated multi-degree-of-freedom systems, it is often necessary to choose linear damping values and determine their locations that will give a desired performance. The method presented in ... -
Dynamic Behavior of Gear Systems and Variation of Coefficient of Friction and Efficiency During the Engagement Cycle
(The American Society of Mechanical Engineers (ASME), 1975)In this work, the instantaneous and average efficiency and coefficient of friction of gear drives operating at low, medium, and moderately high speeds were experimentally and analytically ... -
The Choking Pressure Ratio of a Critical Flow Venturi
(The American Society of Mechanical Engineers (ASME), 1975)The critical flow venturi has many important applications in the measurement and control of gas flow. In many of these applications, it is desirable to minimize the pressure loss required to ... -
Theory for the Effect of Windage on the Lubricant Flow in the Tooth Spaces of Spur Gears
(The American Society of Mechanical Engineers (ASME), 1975) -
Spline Wear-Effects of Design and Lubrication
(The American Society of Mechanical Engineers (ASME), 1975)Spline couplings are widely used to transmit power or drive accessories, or to operate components within accessories. Their principal advantages are mechanical simplicity, compactness and light ... -
Compound Mounting Systems That Incorporate Dynamic Vibration Absorbers
(The American Society of Mechanical Engineers (ASME), 1975)The transmissibility across novel compound or two-stage mounting systems is discussed, and representative calculations of transmissibility are compared for systems with intermediate stages that ... -
On the Application of Response Limiting to Finite Element Structural Analysis Programs
(The American Society of Mechanical Engineers (ASME), 1975)The inclusion of response limiting or “notching” in random vibration design and test requirements for larger equipments such as spacecraft is becoming more commmon. This type of requirement ... -
Response Spectra for Nonlinear Oscillators
(The American Society of Mechanical Engineers (ASME), 1975)Methods are presented for calculating the response spectrum of a nonlinear oscillator with broadband random excitation. A perturbation approach is used for oscillators with slightly nonlinear ... -
Influence of Geometric Imperfections on Vibrational Frequencies of Thin Rings
(The American Society of Mechanical Engineers (ASME), 1975)A relatively thin—thickness to radius ratio—circular ring with rectangular cross section has been investigated to numerically evaluate the effect of eccentricity on the in plane bending natural ... -
The Use of Coherence Techniques to Predict the Effect of Engine Operating Parameters on Diesel Engine Noise
(The American Society of Mechanical Engineers (ASME), 1975)A technique is presented in which the effects on noise of changing diesel engine operating parameters can be predicted. Traditionally, the effects have been determined by experiment. The technique ... -
The Design of Modeled Cam Systems—Part II: Minimization of Motion Distortion Due to Modeling Errors
(The American Society of Mechanical Engineers (ASME), 1975)The dynamic synthesis procedures of Part I are reinforced by qualitative and quantitative results from analysis. The principal concern is for the motion distortion which results from off-speed ... -
Vibrations of a Row of Circular Cylinders in a Liquid
(The American Society of Mechanical Engineers (ASME), 1975)The effects of interaction with surrounding liquid on the dynamic behavior of a row of circular cylinders are studied analytically. First the hydrodynamic forces associated with cylinder motions ... -
Piledriver Noise: Acoustic Radiation From a Cylindrical Pipe Pile Under Periodic Axial Impacts
(The American Society of Mechanical Engineers (ASME), 1975)The acoustic radiation caused by periodic axial impacts on a cylindrical pipe pile of finite length is calculated. The axial velocity at all points on the pile surface is specified in terms ... -
A Least Weight Circular Cooling Fin
(The American Society of Mechanical Engineers (ASME), 1975)The design of the least weight circular cooling fin is obtained through an application of the Minimum Principle. The fin temperature, thickness, and heat flux are considered to be functions ... -
Discussion: “Spline Wear-Effects of Design and Lubrication” (Ku, P. M., and Valtierra, M. L., 1975, ASME J. Eng. Ind., 97, pp. 1257–1263)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Dynamic Behavior of Gear Systems and Variation of Coefficient of Friction and Efficiency During the Engagement Cycle” (Radzimovsky, E., and Mirarefi, A., 1975, ASME J. Eng. Ind., 97, pp. 1274–1280)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “An Experimental and Analytical Study of Connection Forces in High-Speed Mechanisms” (Dubowsky, S., and Young, S. C., 1975, ASME J. Eng. Ind., 97, pp. 1166–1174)
(The American Society of Mechanical Engineers (ASME), 1975) -
A Foundation for a Unified Theory of Analysis of Spatial Mechanisms
(The American Society of Mechanical Engineers (ASME), 1975)In analogy with a spherical (spatial) triangle there are only three fundamental loop equations for any spherical (spatial) polygon, namely the real (dual) sine, sine-cosine, and cosine laws. All ...