Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7521-7540 of 7723
-
Analytical Prediction of the Heat Transfer From a Blood Vessel Near the Skin Surface Cooled by a Symmetrical Strip
(The American Society of Mechanical Engineers (ASME), 1975)A steady-state analytical method has been developed to estimate the amount of heat extracted from a blood vessel running close to the skin surface which is cooled in a symmetrical fashion by ... -
Flow Stress Determination for Metals at Forging Rates and Temperatures
(The American Society of Mechanical Engineers (ASME), 1975)In this study, the uniform compression test is used to determine the flow stress of 403 stainless steel, Waspaloy, Ti-6Al-2Sn-4Zr-2Mo, Inconel 718, Ti-8Mo-8V-2Fe-3Al, and, AISI 4340 at various ... -
The Disk Test for Brittle Materials
(The American Society of Mechanical Engineers (ASME), 1975)The test in which a simple penny shaped disk is loaded along a diameter until it splits is a simple one to perform on brittle materials. However, the interpretation of the results obtained ... -
The Engineering Characteristics of Snow Skis—Part 1: Static Bending and Torsional Characteristics
(The American Society of Mechanical Engineers (ASME), 1975)This paper presents the results of analytical and experimental studies of static bending and torsional characteristics of snow skis. The purpose of the work is to develop analytical and ... -
Plane Strain Forging—A Lower Upper Bound Approach
(The American Society of Mechanical Engineers (ASME), 1975)A general kinematically admissible velocity field applicable to forging of a rectangular strip of a incompressible material is presented. Generalized shape of any dead zone, if assumed, can be ... -
Influence of Transverse Anisotropy on the Plastic Collapse of Plates and Shells
(The American Society of Mechanical Engineers (ASME), 1975)A modification of Tresca’s yield criterion is discussed for plane stress in anisotropic materials, when the yield stress in the thickness direction is higher than in any direction perpendicular ... -
Three-Dimensional Analysis of Form-Relieved Surface of Milling Cutter With Applications
(The American Society of Mechanical Engineers (ASME), 1975)The flank in multi-edge profiled cutters must be designed so that the profile geometry and the correct relief angle at every point of the cutting edge are preserved on repeated radial regrinding. ... -
The Rating of Abrasive Cutoff Wheels
(The American Society of Mechanical Engineers (ASME), 1975)A rational approach to cutoff wheel selection is presented based on the most important criterion for this operation—minimum cost per cut. New parameters are identified which play a more significant ... -
Effects of Tensioning on Buckling and Vibration of Circular Saw Blades
(The American Society of Mechanical Engineers (ASME), 1975)A circular saw blade subjected to a concentrated radial in-plane load and initial tensioning stresses is theoretically investigated by energy methods. The buckling and vibrational properties of ... -
Computer Program to Generate Dimensional and Inertial Properties of the Human Body
(The American Society of Mechanical Engineers (ASME), 1975)A digital computer program has been developed to calculate dimensional and inertial properties of the human body. The program has been designed so that the user may either select a data set ... -
Optimum Chute Profiles in Gravity Flow of Granular Materials: A Discrete Segment Solution Method
(The American Society of Mechanical Engineers (ASME), 1975)Using a single particle model and an assumed resisting force, the problem of finding the required shape of gravity flow discharge chutes to achieve minimum transit time is formulated by breaking ... -
Flanged Acrylic Plastic Hemispherical Shells for Undersea Application
(The American Society of Mechanical Engineers (ASME), 1975)The effects of an equatorial flange and a nonuniform wall thickness upon the critical pressure and stress distribution in acrylic plastic hemispheres have been investigated by experimental and ... -
The Bending Problem of Axially Constrained Beams
(The American Society of Mechanical Engineers (ASME), 1975)The effects of axial constraints on the bending of beams sometimes can be an important factor in the design of apparatus. This nonlinear problem is approached by (a) an exact differential ... -
Vibrations of an Intermediately Supported U-Bend Tube
(The American Society of Mechanical Engineers (ASME), 1975)Vibrations of an intermediately supported U-bend tube fall into two independent classes as an incomplete ring of single span does, namely, the in-plane vibration and the coupled twist-bending ... -
Discussion: “Design of Multi-Recess Hydrostatic Journal Bearings for Minimum Total Power Loss” (Cusano, C., and Conry, T. F., 1974, ASME J. Eng. Ind., 96, pp. 226–232)
(The American Society of Mechanical Engineers (ASME), 1975) -
Tensile Stress Distribution in the Cord of V-Belts
(The American Society of Mechanical Engineers (ASME), 1975) -
Erratum: “Critical Reynolds Number Estimates by Thermodynamic (Stochastic) Methods” (Journal of Engineering for Industry, 1974, 96, pp. 788–794)
(The American Society of Mechanical Engineers (ASME), 1975) -
Discussion: “Machine Tool Chatter: Effect of Surface Slope of Machining Forces During Wave Removing” (Sarnicola, J. F., and Boothroyd, G., 1974, ASME J. Eng. Ind., 96, pp. 1202–1206)
(The American Society of Mechanical Engineers (ASME), 1975) -
Augmented Diffusion in Flowing Blood
(The American Society of Mechanical Engineers (ASME), 1975)An analysis of the simultaneous action of Brownian diffusion and diffusion induced by red blood cell rotation is presented in order to illustrate the form of the combined effect of these two ... -
Discussion: “Critical Reynolds Number Estimates by Thermodynamic (Stochastic) Methods” (Hrycak, P., and Levy, M. J., 1974, ASME J. Eng. Ind., 96, pp. 788–794)
(The American Society of Mechanical Engineers (ASME), 1975)