Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7421-7440 of 7723
-
Analytical and Experimental Investigation of a High-Speed Elastic-Membered Linkage
(The American Society of Mechanical Engineers (ASME), 1976)The paper presents the derivation of the equations of motion of a fully elastic four-bar linkage using the assumed mode analysis approach. The form of the solution for the member deflections ... -
A Comprehensive Study of the Fixed Edge Bending Moments of Thin Rectangular Cantilever Plates Under Point Loading
(The American Society of Mechanical Engineers (ASME), 1976)An experimental program was performed to determine the effect of aspect ratio on point loaded cantilever plate bending moments. The experimental results are compared to theoretical values based ... -
Eccentric Limit Load on Fasteners
(The American Society of Mechanical Engineers (ASME), 1976)In eccentrically loaded joints, both the friction grip and the plastic yield strength can be found by the Pole Concept. Neither yield nor the full friction grip need to develop simultaneously ... -
An Experimental Investigation of Stick-Slip in Hydrostatic Extrusion Using Wax to Simulate Metals
(The American Society of Mechanical Engineers (ASME), 1976)This paper describes an experimental investigation undertaken to check the explanation advanced by Rice and Iyengar for the violent pressure fluctuations which they observed during hydrostatic ... -
On Reciprocating Toroidal Seals
(The American Society of Mechanical Engineers (ASME), 1976)A review of the inverse solution of elastohydrodynamic problems has shown certain conditions on the pressure function and the possible singularity of the film shape. Such a singularity can be ... -
Identification of Structures Through Records Obtained During Strong Earthquake Ground Motion
(The American Society of Mechanical Engineers (ASME), 1976)The problem of estimating a space dependent coefficient in a forced linear hyperbolic differential equation from the knowledge of the solution at one or more isolated points is dealt with. The ... -
Regenerative Drive for Subway Trains—Part 3: System Evaluation
(The American Society of Mechanical Engineers (ASME), 1976)The most efficient hybrid drive philosophy eliminates high-acceleration power peaking and operates as a fully regenerative system (little or no accumulator top-off during station stop). The optimal ... -
Discussion: “Surface Integrity in Machining AISI 4340 Steel” (Bailey, J. A., Jeelani, S., and Becker, S. E., 1976, ASME J. Eng. Ind., 98, pp. 999–1006)
(The American Society of Mechanical Engineers (ASME), 1976) -
A Note on Slip in V-Belt Drives
(The American Society of Mechanical Engineers (ASME), 1976) -
Technology Transfer in the Vibration Analysis of Linearly Tapered Cantilever Beams
(The American Society of Mechanical Engineers (ASME), 1976)Curves are presented for determining the fundamental frequency and several higher harmonics for cantilever beams linearly tapered in the vertical or the horizontal plane or tapered in both planes ... -
Theoretical Thermoelastic Consideration on Accuracy in Machining Metals
(The American Society of Mechanical Engineers (ASME), 1976) -
Regenerative Drive for Subway Trains—Part 1: Mechanical Accumulator Design
(The American Society of Mechanical Engineers (ASME), 1976)A regenerative drive system for subway trains is mathematically modeled and numerically evaluated for the Toronto Bloor-Danforth Subway Line. The scope of the study dictates a multipaper presentation ... -
Synthesis of a Spherical Cycloidal Mechanism
(The American Society of Mechanical Engineers (ASME), 1976)Using rotational displacement matrices to describe spherical motions, closed-form synthesis equations are derived for two rotation matrix mechanisms. These equations are used to calculate the linkage ... -
On Bidirectionally Snapping Linkages
(The American Society of Mechanical Engineers (ASME), 1976)A new criterion for bidirectional snap-buckling has been exploited for the design of two-way snapping linkages that can find many uses. -
Regenerative Drive for Subway Trains—Part 2: Overall System Model
(The American Society of Mechanical Engineers (ASME), 1976)The external system (track, vehicle) for the regenerative drive study is modeled from actual construction drawings and performance specifications. A general duty cycle is constructed and found ... -
Prediction of Cylinder Flow Pressures in Mass-Flow Bins Using Minimum Strain Energy
(The American Society of Mechanical Engineers (ASME), 1976)Jenike, et al. [1] have presented a minimum strain energy theory to predict cylinder flow pressures in mass-flow bins. The complete variation of strain energy pressures is depicted by bounds ... -
Regenerative Drive for Subway Trains—Part 4: Overall System Performance
(The American Society of Mechanical Engineers (ASME), 1976)Vehicle energy consumption and savings for the Toronto Bloor-Danforth Subway Line are evaluated. Two vehicle loads are chosen (for this evaluation) indicative of rush-hour and nonrush-hour operation. ... -
Momentum Balancing of Four-Bar Linkages
(The American Society of Mechanical Engineers (ASME), 1976)The primary objective in this work is the determination of conditions for reducing the angular momentum fluctuations (i.e., vibration) transmitted to the frame of a completely force balanced ... -
A Variational Principle for the Elastodynamic Motion of Planar Linkages
(The American Society of Mechanical Engineers (ASME), 1976)A variational principle is presented that may be used for setting up the equations describing the elastodynamic motion of planar linkages in which all the members are considered to be flexible. ... -
Heuristic Combinatorial Optimization in the Kinematic Design of Mechanisms—Part 2: Applications
(The American Society of Mechanical Engineers (ASME), 1976)The heuristic algorithm, developed in Part 1, is applied here to solve certain realistic mechanisms synthesis problems. These include dimensional synthesis of a rotary-to-linear recording mechanisms ...