Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 7001-7020 of 7723
-
Theory of Linear Continuous Extrusion—Linex
(The American Society of Mechanical Engineers (ASME), 1978)LINEX is a friction actuated, continuous extrusion process for metals. It is fundamentally a linear continuous extrusion process using two-sided gripping of feedstock with the opposed sides being ... -
The Characteristics of Blended Polyester/Cotton Yarns Made by Ring and Open-End Spinning
(The American Society of Mechanical Engineers (ASME), 1978)A blended polyester/cotton yarn has a higher breaking elongation than a cotton yarn because of the rupture of cotton fibers which allows inelastic extension of the yarn. However, the polyester ... -
The Preparation of Calcium Superoxide at Subambient Temperatures and Pressures
(The American Society of Mechanical Engineers (ASME), 1978)We have previously reported on the preparation of calcium superoxide, Ca(O2 )2 , from calcium peroxide diperoxyhydrate, CaO2 ·2H2 O2 . In that work, the preparation of a product of higher ... -
A Study of Wall Ironing by the Finite Element Technique
(The American Society of Mechanical Engineers (ASME), 1978)Wall ironing has been analyzed using an elastic-plastic finite element technique. The effects that the ironing ring semi-cone angle and friction have on the maximum reduction ratio are studied ... -
Discussion: “Surface Effects and Residual Stresses in Electrolytically Ground Steel” (Frisch, J., and Cole, R. R., 1962, ASME J. Eng. Ind., 84, pp. 483–489)
(The American Society of Mechanical Engineers (ASME), 1962) -
Thermal Stresses From a Moving Band Source of Heat on the Surface of a Semi-Infinite Solid
(The American Society of Mechanical Engineers (ASME), 1978)Thermoelastic stresses arising from a moving band source of heat on the surface of a semi-infinite solid have been calculated using well-known temperature solutions and a finite element stress ... -
Combing of Opening Room Blends of Cotton and Polyester
(The American Society of Mechanical Engineers (ASME), 1978)Opening room blends of 1.5 denier and 2.25 denier polyester/cotton were combed to improve blend homogeneity, and their processing and yarn properties were compared with those of conventional ... -
A New Hooked Needle Device For Forming Fiber Beards For Length and Strength Measurement
(The American Society of Mechanical Engineers (ASME), 1978)Research was conducted in the design, development, and evaluation of a new hooked needle device for obtaining from a sample of cotton a parallelized beard of fiber suitable for instrumented ... -
Spherical Acrylic Pressure Hulls With Multiple Penetrations
(The American Society of Mechanical Engineers (ASME), 1978)An experimental program has been conducted to determine the effect of multiple penetrations on the performance of spherical acrylic plastic hulls under external hydrostatic pressure. As test ... -
Analysis of Minimum Crush Deformation in Impact of Vehicles of Different Weight Classes
(The American Society of Mechanical Engineers (ASME), 1978) -
Structural Performance of Acrylic Plastic Plane Disk Windows With Twin Conical Bearing Surfaces
(The American Society of Mechanical Engineers (ASME), 1978)Exploratory investigation into the structural performance of acrylic plastic plane disk windows with twin conical bearing surfaces has shown that such windows behave under hydrostatic loading ... -
On the Thermal Effects in a Warp Beam (A Wound-Yarn-Package)
(The American Society of Mechanical Engineers (ASME), 1978)The development of the stress field in a cylindrically-wound-yarn-package with side flanges (warp beams), during winding, can be predicted [6] using Beddoe’s [4] cylindrically anisotropic continuum ... -
On a New Model of Oblique Cutting
(The American Society of Mechanical Engineers (ASME), 1978) -
The Conflicting Roles of Carbontetrachloride as a Boundary Lubricant
(The American Society of Mechanical Engineers (ASME), 1978)Under certain conditions, carbontetrachloride is found to be a negative boundary lubricant (gives a higher coefficient of friction than that of dry surfaces in air), while under other conditions, ... -
Nonlinear Vibrations of Orthotropic Plates Carrying Concentrated Mass
(The American Society of Mechanical Engineers (ASME), 1978)Following Berger’s approximate method for large deflections, nonlinear transverse free vibrations of an orthotropic right isosceles triangular plate, simply supported along its edges and carrying ... -
Flanged Acrylic Plastic Hemispherical Shells for Undersea Systems—Part 2: Static and Cyclic Fatigue Life Under Hydrostatic Loading
(The American Society of Mechanical Engineers (ASME), 1978)Over 25 acrylic plastic windows with t/Ri = 0.364 in the shape of hemispherical domes with equatorial flanges have been thermoformed from flat sheets and tested under short term, long term, ... -
An Optical Scanning Technique for Measuring Fiber Size
(The American Society of Mechanical Engineers (ASME), 1978)An optical scanning system was used to obtain considerable information related to the fineness and fiber to fiber fineness variability of various samples of natural and man-made staple fibers. ... -
Analytical Prediction of Three Dimensional Cutting Process—Part 2: Chip Formation and Cutting Force with Conventional Single-Point Tool
(The American Society of Mechanical Engineers (ASME), 1978)The cutting model and the energy method to predict chip formation and cutting force, which were proposed in the previous part of this study, are extended to machining with conventional ... -
Optimization of Cold Rolling by Nonlinear Programming
(The American Society of Mechanical Engineers (ASME), 1978)The problem of determining the optimum design parameters of single pass and multipass cold strip rolling is considered. The problem is formulated and solved as a constrained nonlinear programming ... -
Analytical Prediction of Three Dimensional Cutting Process—Part 3: Cutting Temperature and Crater Wear of Carbide Tool
(The American Society of Mechanical Engineers (ASME), 1978)Through the energy method proposed in the previous parts of this study, it is possible to predict chip formation and cutting force for a single point tool of arbitrary geometry. By using the ...